Home

Mazdamanuals.com

DTC P117A:00 [PCM (SKYACTIV-X)]

id0102u9316900

Outline

System malfunction location

Engine oil temperature is high

Detection condition

•  Any one of the following conditions is met:

―  With an engine coolant temperature of 88.5 °C {191 °F} or more while in 5th gear or lower, an engine speed of 5,800 rpm or more continues for 6 min.

―  The estimated engine oil temperature exceeds 136 °C {277 °F} continues for 6 min. (With active air shutter)

Fail-safe

•  Limits engine speed

Possible cause

•  High engine speed condition continues

•  Active air shutter close malfunction

•  PCM malfunction

System wiring diagram

•  Not applicable

Connector diagram

•  Not applicable

System malfunction location	Engine oil temperature is high
Detection condition	• Any one of the following conditions is met: ― With an engine coolant temperature of 88.5 °C {191 °F} or more while in 5th gear or lower, an engine speed of 5,800 rpm or more continues for 6 min. ― The estimated engine oil temperature exceeds 136 °C {277 °F} continues for 6 min. (With active air shutter)
Fail-safe	• Limits engine speed
Possible cause	• High engine speed condition continues • Active air shutter close malfunction • PCM malfunction
System wiring diagram	• Not applicable
Connector diagram	• Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION

•  Record the freeze frame data/snapshot data.

Note

•  Recording can be facilitated using the screen capture function of the PC.

—

Go to the next step.

2

VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY

•  Verify related Service Bulletins, on-line repair information, or Service Information availability.

•  Is any related Information available?

Yes

Perform repair or diagnosis according to the available information.

•  If the vehicle is not repaired, go to the next step.

No

Go to the next step.

3

INSPECT FOR OTHER RELATED DTCs

•  Perform the DTC inspection for the PCM.
(See DTC INSPECTION.)

•  Are any of the following DTCs displayed?

―  P0335:00

―  P059F:00

―  P05A0:00

―  P05A3:00

―  P05C0:00

―  U0284:00

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC P0335:00 [PCM (SKYACTIV-X)].)

(See DTC P059F:00 [PCM (SKYACTIV-X)].)

(See DTC P05A0:00 [PCM (SKYACTIV-X)].)

(See DTC P05A3:00 [PCM (SKYACTIV-X)].)

(See DTC P05C0:00 [PCM (SKYACTIV-X)].)

(See DTC U0284:00 [PCM (SKYACTIV-X)].)

No

Go to the next step.

4

INSPECT VEHICLE CONDITION FOR EFFECT ON MALFUNCTION

•  Verify how the customer drives the vehicle by asking the customer the following:

•  Does the engine speed exceed 5,800 rpm for 6 min or more while driving in 5th gear or lower gear?

Yes

Explain to the customer that the vehicle is normal. (performs control to protect the engine due to continuous engine speed 5,800 rpm for 6 min or more while in 5th gear or lower gear)

If there is a concern with customer’s driving, provide the customer some pertinent advice (such as gear selection, how to use manual mode).

Go to repair completion verification.

No

Go to the next step.

Repair completion verification 1

VERIFY THAT VEHICLE IS REPAIRED

•  Install/connect the part removed/disconnected during the troubleshooting procedure.

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Replicate the vehicle conditions at the time the DTC was detected using the following procedure.

―  Start the engine and warm it up completely.

―  Drive the vehicle.

•  Perform the DTC inspection for the PCM.
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction recurs, replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION [SKYACTIV-X 2.0].)

No

Go to the next step.

Repair completion verification 2

VERIFY IF OTHER DTCs DISPLAYED

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION • Record the freeze frame data/snapshot data. Note • Recording can be facilitated using the screen capture function of the PC.	—	Go to the next step.
2	VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY • Verify related Service Bulletins, on-line repair information, or Service Information availability. • Is any related Information available?	Yes	Perform repair or diagnosis according to the available information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT FOR OTHER RELATED DTCs • Perform the DTC inspection for the PCM. (See DTC INSPECTION.) • Are any of the following DTCs displayed? ― P0335:00 ― P059F:00 ― P05A0:00 ― P05A3:00 ― P05C0:00 ― U0284:00	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC P0335:00 [PCM (SKYACTIV-X)].) (See DTC P059F:00 [PCM (SKYACTIV-X)].) (See DTC P05A0:00 [PCM (SKYACTIV-X)].) (See DTC P05A3:00 [PCM (SKYACTIV-X)].) (See DTC P05C0:00 [PCM (SKYACTIV-X)].) (See DTC U0284:00 [PCM (SKYACTIV-X)].)
3		No	Go to the next step.
4	INSPECT VEHICLE CONDITION FOR EFFECT ON MALFUNCTION • Verify how the customer drives the vehicle by asking the customer the following: • Does the engine speed exceed 5,800 rpm for 6 min or more while driving in 5th gear or lower gear?	Yes	Explain to the customer that the vehicle is normal. (performs control to protect the engine due to continuous engine speed 5,800 rpm for 6 min or more while in 5th gear or lower gear) If there is a concern with customer’s driving, provide the customer some pertinent advice (such as gear selection, how to use manual mode). Go to repair completion verification.
4		No	Go to the next step.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Replicate the vehicle conditions at the time the DTC was detected using the following procedure. ― Start the engine and warm it up completely. ― Drive the vehicle. • Perform the DTC inspection for the PCM. (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-X 2.0].)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTCs DISPLAYED • Perform the DTC inspection. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.