Home

Mazdamanuals.com

SIMULATION TABLE [PCM (SKYACTIV-X)]

SIMULATION TABLE [PCM (SKYACTIV-X)]

 id0102u9350100

—: Not applicable

Simulation item

Unit/Condition

Definition

Operation condition

Engine condition

Other condition
A/C_SW
Off/On
•  Select Off/On to disengage/engage the magnetic clutch.
•  Idle (no load)
—
AIR_BYPASS_VLV_POS_DSD
%
•  Changes % and forcibly drives/stops the air bypass valve.
•  Ignition is switched ON (engine off)
•  Idle (no load)
Note
•  Override drive parameter input range: 0—100%
AIRSHUT_POS_COMD
% Open
•  Changes % to forcibly open/close the active air shutter.
—
Note
•  Override drive parameter input range: 0—100%
CHARGE_LAMP
No(False)/Yes(True)
•  Select No(False)/Yes(True) to turn on/off the charging system warning light.
•  Select No(False)/Yes(True) to display/not display the charging system warning indication on the multi-information display.
•  Ignition is switched ON (engine off)
•  Idle
•  Racing (not idle)
—
CSTR_VENT_SOL_DUTY
Note
•  Displays in the M-MDS but it does not operate.
EGR_COMD
%
•  Changes % and forcibly drives/stops the EGR valve.
•  Ignition is switched ON (engine off)
Note
•  Override drive parameter input range: 0—100%
ENG_COOL_VLV_POS_DUTY
%
•  Changes % and forcibly drives/stops the coolant switching valve.
•  Ignition is switched ON (engine off)
Note
•  Override drive parameter input range: 0—100%
ENG_RPM_DSD
Rpm
•  Changes value (Rpm) to forcibly vary the engine speed.
•  Idle
•  Racing (not idle)
Note
•  Override drive parameter input range: 550—2,000 Rpm
EX_SHUT_VLV_DSD
° (deg)
•  Changes ° (deg) and forcibly drives/stops the exhaust shutter valve.
•  Ignition is switched ON (engine off)
Note
•  Override drive parameter input range: 0—66°
FAN
%
•  Changes % and forcibly drives/stops the fan control module.
•  Ignition is switched ON (engine off)
•  Idle
Note
•  Override drive parameter input range: 0—90%
FP_DUTY
%
•  Changes % and forcibly drives/stops the fuel pump.
•  Ignition is switched ON (engine off)
•  Idle
•  Racing (not idle)
Warning
•  Do not use the simulation function while the fuel hose between the high pressure fuel pump and fuel pump is removed.
Note
•  Override drive parameter input range: 5—95%
FRESH_AIR_DUCT_POS_DSD
Note
•  Displays in the M-MDS but it does not operate.
FUEL_PUMP_REQ
Off/On
•  Select Off/On to forcibly drive/stop the fuel pump.
•  Ignition is switched ON (engine off)
•  Idle
•  Racing (not idle)
—
H_SPD_FAN
Note
•  Displays in the M-MDS but it does not operate.
IMMOBI_MODE
Note
•  Displays in the M-MDS but it does not operate.
IMRC_COMD
%
•  Changes % and forcibly drives/stops the swirl control valve actuator.
•  Ignition is switched ON (engine off)
Note
•  Override drive parameter input range: 0—90%
INJ
Fuel Injector 1 requested closed/
Fuel Injector 2 requested closed/
Fuel Injector 3 requested closed/
Fuel Injector 4 requested closed/
All Fuel Injectors requested closed
•  Forcibly stops the fuel injectors while the engine is idling.
•  Idle
Warning
•  Do not use the simulation function while the vehicle is being driven. Stopping the fuel ejection causes the engine to stall which may cause the brakes to not function.
L_SPD_FAN
Note
•  Displays in the M-MDS but it does not operate.
M_SPD_FAN
Note
•  Displays in the M-MDS but it does not operate.
MIL
Off/On
•  Select Off/On to turn on/off the check engine light.
•  Ignition is switched ON (engine off)
•  Idle
•  Racing (not idle)
—
OIL_PUMP_DUTY
% Duty Cycle
•  Changes % and forcibly drives/stops the engine oil solenoid valve.
•  Ignition is switched ON (engine off)
•  Idle
Note
•  Override drive parameter input range: 0—100%
PRG_DUTY
%
•  Changes % and forcibly drives/stops the purge solenoid valve.
•  Ignition is switched ON (engine off)
•  Idle
Note
•  Override drive parameter 0%: Purge solenoid valve is closed
•  Override drive parameter 100%: Purge solenoid valve is opened
•  Override drive parameter input range: 0—100%
VLV_TIMING_DSD_EX
° (deg)
•  Changes ° (deg) and forcibly drives/stops the exhaust electric variable valve timing motor/driver.
•  Idle
Note
•  Override drive parameter input range: 20—40°
VLV_TIMING_DSD_IN
° (deg)
•  Changes ° (deg) and forcibly drives/stops the intake electric variable valve timing motor/driver.
•  Idle
Note
•  Override drive parameter input range: 33—55°
WHEEL_DRIVE_CTRL_COMD*1
—
•  Forcibly drives/stops the AWD solenoid built into the coupling component.
•  Ignition is switched ON (engine off)
•  Idle
•  Racing (not idle)
Note
•  If the AWD solenoid is forcibly driven, the AWD warning light flashes.
•  Override drive parameter 1: AWD solenoid is stopped
•  Override drive parameter 2: AWD solenoid is operated

*1  :Vehicles with i-ACTIV AWD system