PID/DATA MONITOR TABLE [BODY CONTROL MODULE (BCM) (E)]
id0902r71205s3
|
PID |
Unit/Operation |
Data contents |
Module control terminal |
|---|---|---|---|
|
7GTURN_APPLIED_STAT
|
Off/On
|
• Off: Turn light request signal is not received.
• On: Turn light request signal is received.
|
—
|
|
ACC_RLY
|
Off/On
|
• Off: ACC relay drive is off.
• On: ACC relay drive is on.
|
—
|
|
AGS_NETWORK*1
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: TCM is not equipped.
• Node Attached and Communicate correctly: TCM is equipped, communication with TCM is normal.
• NodeAttached but Not Communicate correctly: TCM is equipped, but communication with TCM is not normal.
|
—
|
|
AIR_INTAKE_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Air intake actuator is not equipped.
• Node Attached and Communicate correctly: Air intake actuator is equipped, communication with air intake actuator is normal.
• NodeAttached but Not Communicate correctly: Air intake actuator is equipped, but communication with air intake actuator is not normal.
|
—
|
|
ALH_HBC_SW*16
|
Off/On
|
• Off: Adaptive LED headlight switch is off.
• On: Adaptive LED headlight switch is on.
|
—
|
|
ALH_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Auto leveling control module/adaptive LED headlights control module is not equipped.
• Node Attached and Communicate correctly: Auto leveling control module/adaptive LED headlights control module is equipped, communication with auto leveling control module/adaptive LED headlights control module is normal.
• NodeAttached but Not Communicate correctly: Auto leveling control module/adaptive LED headlights control module is equipped, but communication with auto leveling control module/adaptive LED headlights control module is not normal.
|
—
|
|
AMB_TEMP
|
°C, °F
|
Displays ambient temperature
|
—
|
|
AMP_CAN_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Audio amplifier is not equipped.
• Node Attached and Communicate correctly: Audio amplifier is equipped, CAN communication with audio amplifier is normal.
• NodeAttached but Not Communicate correctly: Audio amplifier is equipped, but CAN communication with audio amplifier is not normal.
|
—
|
|
AMP_MOST_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Audio amplifier is not equipped.
• Node Attached and Communicate correctly: Audio amplifier is equipped, MOST communication with audio amplifier is normal.
• NodeAttached but Not Communicate correctly: Audio amplifier is equipped, but MOST communication with audio amplifier is not normal.
|
—
|
|
ANTI_THEFT_SYS
|
OFF/ON
|
• OFF: Advanced keyless function is off.
• ON: Advanced keyless function is on.
|
—
|
|
APP
|
%
|
Accelerator pedal opening angle (relative value) with the fully released status as 0% and fully depressed status as 100%
|
—
|
|
AT_IND_NETWORK*1
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Shift position indication is not equipped.
• Node Attached and Communicate correctly: Shift position indication is equipped, communication with shift position indication is normal.
• NodeAttached but Not Communicate correctly: Shift position indication is equipped, but communication with shift position indication is not normal.
|
—
|
|
AUTO_LGHT_OFF
|
Off/On
|
• Off: TNS (parking lights) or headlight off control by auto light off system is not operated.
• On: TNS (parking lights) or headlight off control by auto light off system is operated.
|
—
|
|
BATT_SEN_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Current sensor is not equipped.
• Node Attached and Communicate correctly: Current sensor is equipped, communication with current sensor is normal.
• NodeAttached but Not Communicate correctly: Current sensor is equipped, but communication with current sensor is not normal.
|
—
|
|
BATT_SOC
|
%
|
Battery charge condition (estimated)
|
—
|
|
BBS_NETWORK*2
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Theft-deterrent siren is not equipped.
• Node Attached and Communicate correctly: Theft-deterrent siren is equipped, communication with theft-deterrent siren is normal.
• NodeAttached but Not Communicate correctly: Theft-deterrent siren is equipped, but communication with theft-deterrent siren is not normal.
|
—
|
|
BECM_NETWORK*3
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Mazda M Hybrid battery is not equipped.
• Node Attached and Communicate correctly: Mazda M Hybrid battery is equipped, communication with Mazda M Hybrid battery is normal.
• NodeAttached but Not Communicate correctly: Mazda M Hybrid battery is equipped, but communication with Mazda M Hybrid battery is not normal.
|
—
|
|
BGLR_ALRM
|
NoRequest/RequestControl
|
|
—
|
|
BGLR_ALRM_ANS
|
NoRequest/RequestControl
|
• NoRequest: Hazard warning light flashing answer−back signal is not received.
• RequestControl: Hazard warning light flashing answer−back signal is received.
|
—
|
|
BGLR_ALRM_REQ*4
|
NoRequest/Request
|
• NoRequest: Body control module (BCM) does not operate theft-deterrent horn and hazard warning lights on.
• RequestControl: Body control module (BCM) operates the theft-deterrent horn and hazard warning lights on.
|
—
|
|
BGLR_BACKUP_SIREN*2
|
Off/On
|
• Off: Theft-deterrent siren setting is not turned on.
• On: Theft-deterrent siren setting is turned on.
|
3O
|
|
BGLR_CHARGE*2
|
Charge_OFF_back-up_cells/Charge_On_back-up_cells
|
• Charge_OFF_back-up_cells: Theft-deterrent siren charging is not permitted.
• Charge_On_back-up_cells: Theft-deterrent siren charging is permitted.
|
3O
|
|
BGLR_GAIN*2
|
—
|
Displays the intruder sensor sensitivity set value
|
3O
|
|
BGLR_HZRD_REQ
|
Off/Blink 1 time/Blink 2 times/Blink 3 times
|
• Off: Hazard warning lights are not operated to flash.
• Blink 1 time: Hazard warning lights are operated to flash once.
• Blink 2 times: Hazard warning lights are operated to flash twice.
• Blink 3 times: Hazard warning lights are operated to flash three times.
|
—
|
|
BGLR_IMS*2
|
Sensor Unset/Sensor Set
|
• Sensor Unset: Detection stop signal is sent to intruder sensor.
• Sensor Set: Detection start signal is sent to intruder sensor.
|
3O
|
|
BGLR_IS_COMD*2
|
Sensor Unset/Sensor Set
|
• Sensor Unset: Detection stop signal is sent to inclination sensor.
• Sensor Set: Detection start signal is sent to inclination sensor.
|
3O
|
|
BGLR_SEN*2
|
Off/On
|
• Off: Intruder sensor setting is not turned on.
• On: Intruder sensor setting is turned on.
|
3O
|
|
BGLR_SIREN_COMD*2
|
No_action/StartAudibleAlarm/StopAudibleAlarm/Ignore
|
• No_action: Signal is not sent to theft-deterrent siren.
• StartAudibleAlarm: Alarm start signal is sent to theft-deterrent siren.
• StopAudibleAlarm: Alarm stop signal is sent to theft-deterrent siren.
• Ignore: Normal signal is not sent to theft-deterrent siren.
|
3O
|
|
BGLR_SIREN_MODE*2
|
Set/Unset
|
• Set: Theft-deterrent system is in stand-by mode or alert preparatory mode.
• Unset: Theft-deterrent system is in mode other than above.
|
3O
|
|
BGLR_SLEEP_MODE*2
|
Enter Sleep Mode/Exit Sleep Mode
|
• Enter Sleep Mode: Signal for transition to sleep mode is sent to theft-deterrent siren.
• Exit Sleep Mode: Execute signal is sent to theft-deterrent siren.
|
3O
|
|
BGLR_STAT
|
DEAD/INITIAL/PRE-ARMING/ARMING/ARMING STAND BY/ALARM/ALARM STAND BY
|
• DEAD: Ignition is in ACC or ON (engine off) and alarm cannot be activated.
• INITIAL: Ignition is switched OFF and transition to arming stand-by status is possible.
• PRE-ARMING: Transition period to arming status.
• ARMING: Alarm can be activated by inputting alarm trigger.
• ARMING STAND BY: Liftgate is open under arming status.
• ALARM: Alarm trigger is input and alarm is activated.
• ALARM STAND BY: After alarm activation finished, standing by for next alarm trigger input.
|
—
|
|
B-ISG_NETWORK*3
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Integrated starter generator (ISG) is not equipped.
• Node Attached and Communicate correctly: Integrated starter generator (ISG) is equipped, communication with integrated starter generator (ISG) is normal.
• NodeAttached but Not Communicate correctly: Integrated starter generator (ISG) is equipped, but communication with integrated starter generator (ISG) is not normal.
|
—
|
|
BRK_SW
|
Not Stepping/Stepping
|
• Not Stepping: Brake pedal is not depressed.
• Stepping: Brake pedal is depressed.
|
—
|
|
BRK_SW_1
|
Off/On
|
• Off: Brake switch (No.1 signal) is off.
• On: Brake switch (No.1 signal) is on.
|
—
|
|
C_DOOR_LCK_SW_D
|
Neutral/Lock/Unlock
|
• Neutral: Door lock switch (driver's side) is neither locked nor unlocked.
• Lock: Door lock switch (driver's side) is in lock.
• Unlock: Door lock switch (driver's side) is in unlock.
|
—
|
|
C_DOOR_LCK_SW_P
|
|
||
|
CBCM_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Body control module (BCM) is not equipped.
• Node Attached and Communicate correctly: Body control module (BCM) is equipped, communication with body control module (BCM) is normal.
• NodeAttached but Not Communicate correctly: Body control module (BCM) is equipped, but communication with body control module (BCM) is not normal.
|
—
|
|
CENTER_DISP_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Center display is not equipped.
• Node Attached and Communicate correctly: Center display is equipped, communication with center display is normal.
• NodeAttached but Not Communicate correctly: Center display is equipped, but communication with center display is not normal.
|
—
|
|
CLTCH_INH_SW*5
|
Off/On
|
• Off: Starter interlock switch is off.
• On: Starter interlock switch is on.
|
—
|
|
CMU_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Connectivity master unit (CMU) (except chinese specs.)/audio control unit (ACU) (chinese specs.) is not equipped.
• Node Attached and Communicate correctly: Connectivity master unit (CMU) (except chinese specs.)/audio control unit (ACU) (chinese specs.) is equipped, communication with connectivity master unit (CMU) (except chinese specs.)/audio control unit (ACU) (chinese specs.) is normal.
• NodeAttached but Not Communicate correctly: Connectivity master unit (CMU) (except chinese specs.)/audio control unit (ACU) (chinese specs.) is equipped, but communication with connectivity master unit (CMU) (except chinese specs.)/audio control unit (ACU) (chinese specs.) is not normal.
|
—
|
|
COMMANDER_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Commander switch is not equipped.
• Node Attached and Communicate correctly: Commander switch is equipped, communication with commander switch is normal.
• NodeAttached but Not Communicate correctly: Commander switch is equipped, but communication with commander switch is not normal.
|
—
|
|
CRASH_SIG
|
Off/On
|
• Off: Crash signal is not received.
• On: Crash signal is received.
|
2J, 2L
|
|
Dash-ESU_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Dash-electrical supply unit is not equipped.
• Node Attached and Communicate correctly: Dash-electrical supply unit is equipped, dash-electrical supply unit is normal.
• NodeAttached but Not Communicate correctly: Dash-electrical supply unit is equipped, but communication with dash-electrical supply unit is not normal.
|
—
|
|
DCDC_NETWORK*6
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: DC-DC converter is not equipped.
• Node Attached and Communicate correctly: DC-DC converter is equipped, communication with DC-DC converter is normal.
• NodeAttached but Not Communicate correctly: DC-DC converter is equipped, but communication with DC-DC converter is not normal.
|
—
|
|
DCDC_PCM_NETWORK*3
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: DC-DC converter (Mazda M Hybrid) is not equipped.
• Node Attached and Communicate correctly: DC-DC converter (Mazda M Hybrid) is equipped, communication with DC-DC converter (Mazda M Hybrid) is normal.
• NodeAttached but Not Communicate correctly: DC-DC converter (Mazda M Hybrid) is equipped, but communication with DC-DC converter (Mazda M Hybrid) is not normal.
|
—
|
|
Door_ESU_D_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Door-electrical supply unit (driver's side) is not equipped.
• Node Attached and Communicate correctly: Door-electrical supply unit (driver's side) is equipped, communication with door-electrical supply unit (driver's side) is normal.
• NodeAttached but Not Communicate correctly: Door-electrical supply unit (driver's side) is equipped, but communication with door-electrical supply unit (driver's side) is not normal.
|
—
|
|
Door_ESU_P_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Door-electrical supply unit (passenger's side) is not equipped.
• Node Attached and Communicate correctly: Door-electrical supply unit (passenger's side) is equipped, communication with door-electrical supply unit (passenger's side) is normal.
• NodeAttached but Not Communicate correctly: Door-electrical supply unit (passenger's side) is equipped, but communication with door-electrical supply unit (passenger's side) is not normal.
|
—
|
|
DOOR_LCK_ALL
|
Off/On
|
• Off: All door lock signal is not sent from body control module (BCM).
• On: All door lock signal is sent from body control module (BCM).
|
2J, 2L
|
|
DOOR_LCK_ID_CREATE
|
Off/On
|
Displays door lock control ID creation status.
|
—
|
|
DOOR_SECURITY
|
Off/On
|
Displays door lock control security condition.
|
—
|
|
DOOR_SW_ALL
|
Close/Open
|
• Close: All doors are closed.
• Open: Any door is open.
|
—
|
|
DOOR_SW_D
|
Close/Open
|
• Close: Front door (driver's side) is closed.
• Open: Front door (driver's side) is open.
|
2J, 2L
|
|
DOOR_SW_L/R
|
Close/Open
|
• Close: Rear door (LH) is closed.
• Open: Rear door (LH) is open.
|
2J, 2L
|
|
DOOR_SW_P
|
Close/Open
|
• Close: Front door (passenger's side) is closed.
• Open: Front door (passenger's side) is open.
|
2J, 2L
|
|
DOOR_SW_R/R
|
Close/Open
|
• Close: Rear door (RH) is closed.
• Open: Rear door (RH) is open.
|
2J, 2L
|
|
DOOR_ULCK_ALL
|
Off/On
|
• Off: All door unlock signal is not sent from body control module (BCM).
• On: All door unlock signal is sent from body control module (BCM).
|
2J, 2L
|
|
DOOR_ULCK_D
|
Off/On
|
• Off: Front door (driver's side) unlock request signal is not sent from body control module (BCM).
• On: Front door (driver's side) unlock request signal is sent from body control module (BCM).
|
2J, 2L
|
|
DRL
|
Off/Activating as EU_DRL
|
• Off: Daytime running light (DRL) is not turned on.
• Activating as EU_DRL: Daytime running light (DRL) is turned on.
|
—
|
|
DRL_REQ
|
Off/On
|
• Off: Body control module (BCM) does not operate daytime running light (DRL) on.
• On: Body control module (FBCM) operates the daytime running light (DRL) on.
|
—
|
|
DSC_PT_BUS_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
Without Mazda M Hybrid
• Node is not attached on Vehicle: DSC HU/CM is not equipped.
• Node Attached and Communicate correctly: DSC HU/CM is equipped, communication via CAN BUS No.2 with DSC HU/CM is normal.
• NodeAttached but Not Communicate correctly: DSC HU/CM is equipped, but communication via CAN BUS No.2 with DSC HU/CM is not normal.
With Mazda M Hybrid
• Node is not attached on Vehicle: Electronically controlled brake unit is not equipped.
• Node Attached and Communicate correctly: Electronically controlled brake unit is equipped, communication via CAN BUS No.2 with electronically controlled brake unit is normal.
• NodeAttached but Not Communicate correctly: Electronically controlled brake unit is equipped, but communication via CAN BUS No.2 with electronically controlled brake unit is not normal.
|
—
|
|
DSC_VEH_BUS_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
Without Mazda M Hybrid
• Node is not attached on Vehicle: DSC HU/CM is not equipped.
• Node Attached and Communicate correctly: DSC HU/CM is equipped, communication via CAN BUS No.1 with DSC HU/CM is normal.
• NodeAttached but Not Communicate correctly: DSC HU/CM is equipped, but communication via CAN BUS No.1 with DSC HU/CM is not normal.
With Mazda M Hybrid
• Node is not attached on Vehicle: Electronically controlled brake unit is not equipped.
• Node Attached and Communicate correctly: Electronically controlled brake unit is equipped, communication via CAN BUS No.1 with electronically controlled brake unit is normal.
• NodeAttached but Not Communicate correctly: Electronically controlled brake unit is equipped, but communication via CAN BUS No.1 with electronically controlled brake unit is not normal.
|
—
|
|
DSM_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Position memory control module is not equipped.
• Node Attached and Communicate correctly: Position memory control module is equipped, communication via CAN BUS No.1 with position memory control module is normal.
• NodeAttached but Not Communicate correctly: Position memory control module is equipped, but communication via CAN BUS No.1 with position memory control module is not normal.
|
—
|
|
DVD_NETWORK*7
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: DVD/CD player is not equipped.
• Node Attached and Communicate correctly: DVD/CD player is equipped, communication with DVD/CD player is normal.
• NodeAttached but Not Communicate correctly: DVD/CD player is equipped, but communication with DVD/CD player is not normal.
|
—
|
|
ENG_RPM_VSPD_RATIO
|
Rpm/Kph
|
Displays engine speed
|
—
|
|
ENG_STARTER_VOLT_1
|
V
|
Displays voltage at body control module (BCM) terminal 2T
|
2T
|
|
ENG_STARTER_VOLT_2
|
V
|
Displays voltage at body control module (BCM) terminal 2AD
|
2AD
|
|
ENG_STAT
|
Off/Ready/Cranking/Running/Stalled/Afterrun/Shutdown/Not defined
|
Displays engine condition
|
—
|
|
EPS_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Electric Power Steering (EPS) control module is not equipped.
• Node Attached and Communicate correctly: Electric Power Steering (EPS) control module is equipped, communication with Electric Power Steering (EPS) control module is normal.
• NodeAttached but Not Communicate correctly: Electric Power Steering (EPS) control module is equipped, but communication with Electric Power Steering (EPS) control module is not normal.
|
—
|
|
ESS_HZRD
|
NoRequest/RequestControl
|
• NoRequest: Hazard warning light request signal is not received during the emergency stop signal system (ESS) operation.
• RequestControl: Hazard warning light request signal is received during the emergency stop signal system (ESS) operation.
|
—
|
|
ESU_CAN_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Electrical supply unit (ESU) is not equipped.
• Node Attached and Communicate correctly: Electrical supply unit (ESU) is equipped, CAN communication with electrical supply unit (ESU) is normal.
• NodeAttached but Not Communicate correctly: Electrical supply unit (ESU) is equipped, but CAN communication with electrical supply unit (ESU) is not normal.
|
—
|
|
ESU_LIN_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Electrical supply unit (ESU) is not equipped.
• Node Attached and Communicate correctly: Electrical supply unit (ESU) is equipped, LIN communication with electrical supply unit (ESU) is normal.
• NodeAttached but Not Communicate correctly: Electrical supply unit (ESU) is equipped, but LIN communication with electrical supply unit (ESU) is not normal.
|
—
|
|
EXT_T/LGT_REL_SW
|
Off/On
|
• Off: Liftgate opener switch is not pressed.
• On: Liftgate opener switch is pressed.
|
4J
|
|
F_WASH_CTRL_ALLW
|
Wash_Allowed/Not_Allowed
|
• Wash_Allowed: Use of windshield washer is permitted.
• Not_Allowed: Use of windshield washer is not permitted.
|
—
|
|
F_WASH_SW
|
Off/On
|
• Off: Windshield washer switch is off.
• On: Windshield washer switch is on.
|
—
|
|
F_WIP
|
OFF/FrontWiper On Lo/FrontWiper On Hi/FrontWiperINT Auto On
|
• OFF: Windshield wiper switch is in the OFF position.
• FrontWiper On Lo: Windshield wiper switch is in the LO position.
• FrontWiper On Hi: Windshield wiper switch is in the HI position.
• FrontWiperINT Auto On: Windshield wiper switch is in the INT position.
|
—
|
|
F_WIP_ANG_SEN_FAIL
|
Not_Failure/Failure
|
• Not_Failure: Position sensor in the windshield wiper motor is normal.
• Failure: Position sensor in the windshield wiper motor has a malfunction.
|
—
|
|
F_WIP_CTRL
|
F.WiperOff/F.WiperLo/F.WiperHi
|
• F.WiperOff: Windshield wipers are not operated.
• F.WiperLo: Windshield wipers are operated at low speed.
• F.WiperHi: Windshield wipers are operated at high speed.
|
—
|
|
F_WIP_FET_FAIL
|
Not_Failure/Failure
|
• Not_Failure: FET circuit is normal.
• Failure: FET circuit has a malfunction.
|
—
|
|
F_WIP_INT_VOL
|
%
|
Displays windshield wiper INT level signal value received
|
—
|
|
F_WIP_POS
|
Unknown/Parking_Position/Not_Parking_Position
|
• Unknown: Windshield wipers position is not determined.
• Parking_Position: Windshield wipers in park position.
• Not_Parking_Position: Windshield wipers in position other than park.
|
—
|
|
F_WIP_REG_FAIL
|
Not_Failure/Failure
|
• Not_Failure: Windshield wiper regulator is normal.
• Failure: Windshield wiper regulator is not normal.
|
—
|
|
F_WIP_REQ
|
Off/Stop(ParkingPosition)/F.WiperLo/F.WiperHi/Stop(ServicePosition)/Stop(CurrentPosition)
|
• Off: Body control module (BCM) does not operate windshield wipers.
• Stop(ParkingPosition): Body control module (BCM) operates windshield wipers to the park position.
• F.WiperLo: Body control module (BCM) operates windshield wipers at low speed.
• F.WiperHi: Body control module (BCM) operates windshield wipers at high speed.
• Stop(ServicePosition): Body control module (BCM) operates windshield wipers to the service position.
• Stop(CurrentPosition): Body control module (BCM) operates windshield wipers to the current position.
|
—
|
|
F_WIP_ROT_FAIL
|
Not_Failure/Failure
|
• Not_Failure: Windshield wiper rotation direction is normal.
• Failure: Windshield wiper rotation direction is not normal.
|
—
|
|
F_WIP_TEACH_STAT_SUB
|
No_Sub_Status/Detect_jig_out_of_area/Unusually_Mode_Switch/DataFlash_Failure/FrontWipr_Failure
|
• No_Sub_Status: Body control module (BCM) cannot receive any signal from windshield wiper arm and blade.
• Detect_jig_out_of_area: Windshield wiper arm and blade movement is detected to be outside of specified range.
• Unusually_Mode_Switch: Windshield wiper and washer switch is not normal.
• DataFlash_Failure: Data is not normal.
• FrontWipr_Failure: Windshield wipers are malfunctioning.
|
—
|
|
F_WIP_THRM_FAIL
|
Not_Failure/Failure
|
• Not_Failure: Circuit detecting windshield wiper motor temperature is not normal.
• Failure: Circuit detecting windshield wiper motor temperature is normal.
|
—
|
|
F_WIP_TIME_FAIL
|
Not_Failure/Failure
|
• Not_Failure: Windshield wiper is operating normally.
• Failure: Windshield wiper operating speed is extremely slow (when the Windshield wiper is operating).
|
—
|
|
F_WIP_VOLT_FAIL
|
Voltage_Detection_Failure/Not_Failure
|
• Voltage_Detection_Failure: Circuit detecting windshield wiper motor voltage is not normal.
• Not_Failure: Circuit detecting windshield wiper motor voltage is normal.
|
—
|
|
FR_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Front radar sensor is not equipped.
• Node Attached and Communicate correctly: Front radar sensor is equipped, communication with front radar sensor is normal.
• NodeAttached but Not Communicate correctly: Front radar sensor is equipped, but communication with front radar sensor is not normal.
|
—
|
|
FSC_LGHT_REQ
|
Off/On
|
• Off: Headlight HI is turned on.
• On: Headlight HI is turned off.
|
—
|
|
FSC_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Forward sensing camera (FSC) is not equipped.
• Node Attached and Communicate correctly: Forward sensing camera (FSC) is equipped, communication with forward sensing camera (FSC) is normal.
• NodeAttached but Not Communicate correctly: Forward sensing camera (FSC) is equipped, but communication with forward sensing camera (FSC) is not normal.
|
—
|
|
FSM_REQ
|
|
||
|
FSRL_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Front side radar sensor (LH) is not equipped.
• Node Attached and Communicate correctly: Front side radar sensor (LH) is equipped, communication with front side radar sensor (LH) is normal.
• NodeAttached but Not Communicate correctly: Front side radar sensor (LH) is equipped, but communication with front side radar sensor (LH) is not normal.
|
—
|
|
FSRR_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Front side radar sensor (RH) is not equipped.
• Node Attached and Communicate correctly: Front side radar sensor (RH) is equipped, communication with front side radar sensor (RH) is normal.
• NodeAttached but Not Communicate correctly: Front side radar sensor (RH) is equipped, but communication with front side radar sensor (RH) is not normal.
|
—
|
|
FUEL_AMOUNT
|
L
|
Displays fuel level detected by the fuel gauge
|
2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
|
|
FUEL_GAUGE_RES_MAIN
|
Ohm
|
Displays fuel gauge sender unit resistance value
|
2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
|
|
FUEL_GAUGE_RES_SUB*8
|
Ohm
|
Displays fuel gauge sender unit (sub) resistance value
|
2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
|
|
FUEL_GAUGE_VOLT_MAIN
|
V
|
Displays fuel gauge sender unit voltage value
|
2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
|
|
FUEL_GAUGE_VOLT_SUB*8
|
V
|
Displays fuel gauge sender unit (sub) voltage value
|
2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
|
|
GLOBAL_REAL_TIME
|
min
|
Displays cumulative elapsed time since vehicle completion
|
—
|
|
GLOWPLUG_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/ NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Glow plug is not equipped.
• Node Attached and Communicate correctly: Glow plug is equipped, communication with glow plug is normal.
• NodeAttached but Not Communicate correctly: Glow plug is equipped, but communication with glow plug is not normal.
|
—
|
|
H/L_CLEAN_RLY
|
Off/On
|
• Off: Headlight cleaner relay is off.
• On: Headlight cleaner relay is on.
|
—
|
|
H/L_HI
|
Off/On
|
• Off: Headlight HI signal is not sent from body control module (BCM).
• On: Headlight HI signal is sent from body control module (BCM).
|
—
|
|
H/L_HI_SW
|
Off/On
|
• Off: Light switch HI signal is not received.
• On: Light switch HI signal is received.
|
—
|
|
H/L_LO_REQ
|
Off/On
|
• Off: Body control module (BCM) does not operate the headlight LO off.
• On: Body control module (BCM) does not operate the headlight LO on.
|
—
|
|
H/L_LO_SW
|
Off/On
|
• Off: Other than light switch LO position of light switch is received.
• On: Light switch LO position of light switch is received.
|
—
|
|
H/L_LVL_CSTMZ
|
Not Adopted/0/0.5/1/1.5/2/2.5/3/3.5/4/4.5/5
|
Display headlight manual leveling system set position.
|
—
|
|
H/L_OFF_SW
|
Off/On
|
• Off: Light switch OFF signal is not received.
• On: Light switch OFF signal is received.
|
—
|
|
H/L_PASSING_SW
|
Off/On
|
• Off: Light switch FLASH−TO−PASS signal is not received.
• On: Light switch FLASH−TO−PASS signal is received.
|
—
|
|
HOOD_SW
|
Close/Open
|
• Close: Hood is closed.
• Open: Hood is open.
|
2S
|
|
HUD_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Active Driving Display (ADD) is not equipped.
• Node Attached and Communicate correctly: Active Driving Display (ADD) is equipped, communication with Active Driving Display (ADD) is normal.
• NodeAttached but Not Communicate correctly: Active Driving Display (ADD) is equipped, but communication with Active Driving Display (ADD) is not normal.
|
—
|
|
HZRD_REQ
|
NoRequest/RequestControl
|
• NoRequest: Body control module (BCM) does not operate the hazard warning light on.
• RequestControl: Body control module (BCM) operates the hazard warning light on.
|
—
|
|
HZRD_SW
|
Off/On/Unknown
|
• Off: Hazard warning switch is not pressed.
• On: Hazard warning switch is pressed.
• Unknown: Hazard warning switch on/off is not determined.
|
—
|
|
ICM_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Instrument cluster is not equipped.
• Node Attached and Communicate correctly: Instrument cluster is equipped, communication with instrument cluster is normal.
• NodeAttached but Not Communicate correctly: Instrument cluster is equipped, but communication with instrument cluster is not normal.
|
—
|
|
IG_ON_TIMER
|
Min
|
Time since engine start
|
—
|
|
IG1_RLY
|
Off/On
|
• Off: IG1 relay drive is off.
• On: IG1 relay drive is on.
|
—
|
|
IMMOBI_IDENTIFY
|
FALSE/TRUE
|
• FALSE: Verified remote transmitter ID programmed information does not match remote transmitter ID after steering lock is released.
• TRUE: Verified remote transmitter ID programmed information matches remote transmitter ID after steering lock is released.
|
—
|
|
IMMOBI_OPERAT_MODE
|
Operation Mode 1/Operation Mode 2/Operation Mode 3/Operation Mode 4/Operation Mode 5/Operation Mode 6/Operation Mode 7
|
Displays immobilizer system operation mode
|
—
|
|
IMS_NETWORK*2
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Intruder sensor is not equipped.
• Node Attached and Communicate correctly: Intruder sensor is equipped, communication with intruder sensor is normal.
• NodeAttached but Not Communicate correctly: Intruder sensor is equipped, but communication with intruder sensor is not normal.
|
—
|
|
IND_ASSY_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Indicator unit is not equipped.
• Node Attached and Communicate correctly: Indicator unit is equipped, communication with indicator unit is normal.
• NodeAttached but Not Communicate correctly: Indicator unit is equipped, but communication with indicator unit is not normal.
|
—
|
|
IP-ESU_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Climate control unit is not equipped.
• Node Attached and Communicate correctly: Climate control unit is equipped, communication with climate control unit is normal.
• NodeAttached but Not Communicate correctly: Climate control unit is equipped, but communication with climate control unit is not normal.
|
—
|
|
KEY_ANS_REQ
|
NoRequest/RequestControl
|
• NoRequest: Hazard warning light flashing answer−back signal is not received.
• RequestControl: Hazard warning light flashing answer−back signal is received.
|
—
|
|
KEY_BUZZER
|
Off/On
|
• Off: Keyless beeper is not operated to sound.
• On: Keyless beeper is operated to sound.
|
2AA, 2AB
|
|
KEY_ENA
|
Disabled/Enabled
|
• Disabled: Immobilizer system is disabled.
• Enabled: Immobilizer system is enabled.
|
—
|
|
LATCH_IP_SW
|
Off/On
|
• Off: Power liftgate (PLG) front switch is not pressed.
• On: Power liftgate (PLG) front switch is pressed.
|
—
|
|
LCML_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Light control module (LH) is not equipped.
• Node Attached and Communicate correctly: Light control module (LH) is equipped, communication with light control module (LH) is normal.
• NodeAttached but Not Communicate correctly: Light control module (LH) is equipped, but communication with light control module (LH) is not normal.
|
—
|
|
LCMR_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Light control module (RH) is not equipped.
• Node Attached and Communicate correctly: Light control module (RH) is equipped, communication with light control module (RH) is normal.
• NodeAttached but Not Communicate correctly: Light control module (RH) is equipped, but communication with light control module (RH) is not normal.
|
—
|
|
LFU_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: LF control unit is not equipped.
• Node Attached and Communicate correctly: LF control unit is equipped, communication with LF control unit is normal.
• NodeAttached but Not Communicate correctly: LF control unit is equipped, but communication with LF control unit is not normal.
|
—
|
|
LLINK_SW_D
|
Unlock/Neutral/Lock/Failure
|
• Unlock: Front door lock−link switch (driver's side) is in unlock.
• Neutral: Front door lock−link switch (driver's side) is not in lock and unlock.
• Lock: Front door lock−link switch (driver's side) is in lock.
• Failure: Front door lock−link switch (driver's side) has a malfunction.
|
—
|
|
LLINK_SW_P
|
Unlock/Lock
|
• Unlock: Front door lock−link switch (passenger's side) is in unlock.
• Lock: Front door lock−link switch (passenger's side) is in lock.
|
—
|
|
LLINK_SW_R
|
Unlock/Lock
|
• Unlock: Rear door lock−link switch (LH), rear door lock−link switch (RH) are in unlock.
• Lock: Rear door lock−link switch (LH), rear door lock−link switch (RH) are in lock.
|
4F
|
|
LLINK_SW_STAT_R
|
Off/On
|
• Off: Front door lock−link switch (LH) is in unlock.
• On: Front door lock−link switch (LH) is in lock.
|
—
|
|
MASTER_KEY
|
No/Yes
|
• No: There is no master key.
• Yes: There is master key.
|
—
|
|
MODE_ACTAT_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Airflow mode actuator is not equipped.
• Node Attached and Communicate correctly: Airflow mode actuator is equipped, communication with airflow mode actuator is normal.
• NodeAttached but Not Communicate correctly: Airflow mode actuator is equipped, but communication with airflow mode actuator is not normal.
|
—
|
|
MODE_PS_ACTAT_NETWORK
|
|
||
|
MTTR_TIMER
|
hour
|
If the ignition is switched OFF after a specified time has elapsed or the vehicle has been driven for a specified period of time or more while in the fail-safe mode, the ignition will remain switched off and the engine cannot be started. Displays the elapsed time since the engine could no longer be started.
|
—
|
|
NOX1_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: NOx sensor No.1 is not equipped.
• Node Attached and Communicate correctly: NOx sensor No.1 is equipped, communication with NOx sensor No.1 is normal.
• NodeAttached but Not Communicate correctly: NOx sensor No.1 is equipped, but communication with NOx sensor No.1 is not normal.
|
—
|
|
NOX2_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: NOx sensor No.2 is not equipped.
• Node Attached and Communicate correctly: NOx sensor No.2 is equipped, communication with NOx sensor No.2 is normal.
• NodeAttached but Not Communicate correctly: NOx sensor No.2 is equipped, but communication with NOx sensor No.2 is not normal.
|
—
|
|
OHC_ROOMLAMP_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Front map light is not equipped.
• Node Attached and Communicate correctly: Front map light is equipped, communication with front map light is normal.
• NodeAttached but Not Communicate correctly: Front map light is equipped, but communication with front map light is not normal.
|
—
|
|
OIL_LVL_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Engine oil level sensor is not equipped.
• Node Attached and Communicate correctly: Engine oil level sensor is equipped, communication with engine oil level sensor is normal.
• NodeAttached but Not Communicate correctly: Engine oil level sensor is equipped, but communication with engine oil level sensor is not normal.
|
—
|
|
OMC_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Driver monitoring camera unit is not equipped.
• Node Attached and Communicate correctly: Driver monitoring camera unit is equipped, communication with driver monitoring camera unit is normal.
• NodeAttached but Not Communicate correctly: Driver monitoring camera unit is equipped, but communication with driver monitoring camera unit is not normal.
|
—
|
|
OMM_LGHT_OFF
|
Off/On
|
• Off: Battery discharge suppression signal is not sent from body control module (BCM).
• On: Battery discharge suppression signal is sent from body control module (BCM).
|
—
|
|
ONE_TOUCH_TURN
|
Off/On
|
• Off: Turn switch LH signal or the turn switch RH signal is not received.
• On: Turn switch LH signal or the turn switch RH signal is received.
|
—
|
|
OUTLET_L1_REQ
|
Off/On
|
|
—
|
|
OUTLET_R1_REQ
|
Off/On
|
|
—
|
|
PARK_RANGE_SW
|
Off/On
|
• Off: NOT P position switch is off.
• On: NOT P position switch is on.
|
—
|
|
PCM_PT_BUS_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: PCM is not equipped.
• Node Attached and Communicate correctly: PCM is equipped, communication via CAN BUS No.2 with PCM is normal.
• NodeAttached but Not Communicate correctly: PCM is equipped, but communication via CAN BUS No.2 with is not normal.
|
—
|
|
PCM_VEH_BUS_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: PCM is not equipped.
• Node Attached and Communicate correctly: PCM is equipped, communication via CAN BUS No.1 with PCM is normal.
• NodeAttached but Not Communicate correctly: PCM is equipped, but communication via CAN BUS No.1 with PCM is not normal.
|
—
|
|
PLG_NETWORK*17
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Power liftgate (PLG) control module is not equipped.
• Node Attached and Communicate correctly: Power liftgate (PLG) control module is equipped, communication with power liftgate (PLG) control module is normal.
• NodeAttached but Not Communicate correctly: Power liftgate (PLG) control module is equipped, but communication with power liftgate (PLG) control module is not normal.
|
—
|
|
PMS_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Position memory control module is not equipped.
• Node Attached and Communicate correctly: Position memory control module is equipped, communication with position memory control module is normal.
• NodeAttached but Not Communicate correctly: Position memory control module is equipped, but communication with position memory control module is not normal.
|
—
|
|
PNC_ALRM_HZRD
|
NoRequest/RequestControl
|
• Off: Hazard warning light flashing request signal is not received.
• On: Hazard warning light flashing request signal is received.
|
—
|
|
PNC_ALRM_REQ
|
NoRequest/RequestControl
|
|
—
|
|
POWER_MODE
|
OFF/ACC/ON/CRANK
|
• OFF: Body control module (BCM) controls ignition switch off (lock).
• ACC: Body control module (BCM) controls ignition switch ACC.
• ON: Body control module (BCM) controls ignition switch ON (engine off).
• CRANK: Body control module (BCM) controls cranking at ignition switch ON.
|
—
|
|
PSM_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Parking assist unit (ultrasonic) is not equipped.
• Node Attached and Communicate correctly: Parking assist unit (ultrasonic) is equipped, communication with parking assist unit (ultrasonic) is normal.
• NodeAttached but Not Communicate correctly: Parking assist unit (ultrasonic) is equipped, but communication with parking assist unit (ultrasonic) is not normal.
|
—
|
|
PTC_HEAT_NETWORK*9
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: PTC heater is not equipped.
• Node Attached and Communicate correctly: PTC heater is equipped, communication with PTC heater is normal.
• NodeAttached but Not Communicate correctly: PTC heater is equipped, but communication with PTC heater is not normal.
|
—
|
|
R_FOG_SW_IN
|
Off/On
|
• Off: Rear fog light switch is off.
• On: Rear fog light switch is on.
|
—
|
|
R_FOG_SW_OUT
|
Inactive/Active
|
• Inactive: Rear fog light is turned off.
• Active: Rear fog light is turned on.
|
—
|
|
R_MIX_ACTAT_NETWORK
|
|
||
|
R_TIMER_MODE
|
OFF/ON
|
• OFF: Intermittent wiper operation of rear wiper is disabled.
• ON: Intermittent wiper operation of rear wiper is enabled.
|
—
|
|
R_VENT_ACTAT_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Rear vent actuator is not equipped.
• Node Attached and Communicate correctly: Rear vent actuator is equipped, communication with rear vent actuator is normal.
• NodeAttached but Not Communicate correctly: Rear vent actuator is equipped, but communication with rear vent actuator is not normal.
|
—
|
|
R_WASH_SW
|
Off/On
|
• Off: Rear wiper and washer switch is not in rear washer position.
• On: Rear wiper and washer switch is in rear washer position.
|
—
|
|
R_WIP
|
Off/RearWiperLo/Not defined/WiperINT
|
• Off: Rear wiper and washer switch is in the OFF position.
• RearWiperLo: Rear wiper and washer switch is in the ON position.
• Not defined: Rear wiper and washer switch position is not determined.
• WiperINT: Rear wiper and washer switch is in the INT position.
|
—
|
|
R_WIP_CTRL
|
Deactivate/Activate/Fail(Circuit Short to Ground)/Fail(Circuit Open)/Fail(Circuit Short to Battery)
|
Rear wiper operation condition input signal from electrical supply unit (ESU)
• Deactivate: Rear wiper is not operated.
• Activate: Rear wiper is operated.
• Fail(Circuit Short to Ground): Short to ground circuit malfunction is received from rear wiper.
• Fail(Circuit Open): Open circuit malfunction is received from rear wiper.
• Fail(Circuit Short to Battery): Short to battery circuit malfunction is received from rear wiper.
|
—
|
|
R_WIP_POS
|
Unknown/Parking_Position/Not_Parking_Position/AS_SW_Failure
|
• Unknown: Rear wiper position is not determined.
• Parking_Position: Rear wiper in park position.
• Not_Parking_Position: Rear wiper in position other than park.
• AS_SW_Failure: Autostop switch has a malfunction.
|
—
|
|
R_WIP_REQ
|
Off/Rear Wiper Low On/Stop
|
• Off: Body control module (BCM) does not operate rear wiper.
• Rear Wiper Low On: Body control module (BCM) operates rear wiper.
• Stop: Body control module (BCM) operates rear wiper to the park position.
|
—
|
|
R_WIP_STALL_STAT
|
OK/Stall
|
• OK: Rear wiper motor is normal.
• Stall: Rear wiper motor is stalled.
|
—
|
|
RCM_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Sophisticated Airbag Sensor (SAS) control module is not equipped.
• Node Attached and Communicate correctly: Sophisticated Airbag Sensor (SAS) control module is equipped, communication with Sophisticated Airbag Sensor (SAS) control module is normal.
• NodeAttached but Not Communicate correctly: Sophisticated Airbag Sensor (SAS) control module is equipped, but communication with Sophisticated Airbag Sensor (SAS) control module is not normal.
|
—
|
|
REGEN_NETWORK*3
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Mazda M Hybrid is not equipped.
• Node Attached and Communicate correctly: Mazda M Hybrid is equipped, communication with Mazda M Hybrid is normal.
• NodeAttached but Not Communicate correctly: Mazda M Hybrid is equipped, but communication with Mazda M Hybrid is not normal.
|
—
|
|
RES
|
Off/On
|
|
—
|
|
RES_HZRD_ANS
|
NoRequest/RequestControl
|
|
—
|
|
RF_TMTR
|
FALSE/TRUE
|
• FALSE: Remote transmitter ID information is not programmed in LF control unit.
• TRUE: Remote transmitter ID information is programmed in LF control unit.
|
—
|
|
RLS_AMB_TEMP*11
|
°C, °F
|
Displays rain sensor ambient temperature.
|
—
|
|
RLS_AUTO_LGHT_REQ*10
|
TNSOff/Head_Off/TNSOn/HeadOff/TNSOn/HeadOn
|
Illumination request by receiving TNS or headlight illumination request signal.
• TNSOff/Head_Off: Body control module (BCM) does not operate the TNS (parking lights) and headlight on.
• TNSOn/HeadOff:Body control module (BCM) operates the TNS (parking lights) on.
• TNSOn/HeadOn: Body control module (BCM) operates the TNS (parking lights) and headlight on.
|
—
|
|
RLS_CTRL*10
|
OFF/TNS Only ON/Low and TNS/Unknown
|
Illumination request by receiving auto light signal, TNS or headlight illumination request signal.
• OFF: Body control module (BCM) does not operate the TNS (parking lights) and headlight on.
• TNS Only ON: Body control module (BCM) operates the TNS (parking lights) on.
• Low and TNS: Body control module (BCM) operates the TNS (parking lights) and headlight on.
• Unknown: TNS (parking lights) condition is not detected.
|
—
|
|
RLS_FAIL*10
|
Normal/Fault
|
• Normal: Error signals is not received from the auto light sensor.
• Fault: Error signals is received from the auto light sensor.
|
—
|
|
RLS_FAIL_STAT*10
|
Faulty(Faulty)/Initialize/Not within specifications/Normal(sensing)
|
Displays auto light sensor condition input signal
|
—
|
|
RLS_FWD_LGHT_SEN*10
|
OK/NG
|
• OK: Normal forward brightness can be detected.
• NG: Normal forward brightness cannot be detected.
|
—
|
|
RLS_I_ILLMI_MODE*10
|
Unknown/Off(day_mode)/On(night_mode)
|
• Unknown: Panel light illumination request signal is not determined.
• Off(day_mode): Panel light illumination request signal is not received.
• On(night_mode): Panel light illumination request signal is received.
|
—
|
|
RLS_LGHT_SEN_FAIL*10
|
Normal/Fault
|
• Normal: Error signals is not received from the auto light sensor.
• Fault: Error signals is received from the auto light sensor.
|
—
|
|
RLS_NETWORK*10,*11,or*12
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Humidity sensor /solar radiation sensor /auto light sensor /rain sensor is not equipped.
• Node Attached and Communicate correctly: Humidity sensor /solar radiation sensor /auto light sensor /rain sensor is equipped, communication with humidity sensor /solar radiation sensor /auto light sensor /rain sensor is normal.
• NodeAttached but Not Communicate correctly: Humidity sensor /solar radiation sensor /auto light sensor /rain sensor is equipped, but communication with humidity sensor /solar radiation sensor /auto light sensor /rain sensor is not normal.
|
—
|
|
RLS_RAIN_SEN_FAIL*11
|
Off/On
|
• Off: Error signals is not received from the rain sensor.
• On: Error signals is received from the rain sensor.
|
—
|
|
RLS_RELAT_HMDTY
|
%
|
Displays relative humidity.
|
—
|
|
RLS_STAT*10
|
Off/TNS On requested/TNS/Headlight On requested
|
• Off: TNS (parking lights) and headlight illumination request signal is not received.
• TNS On requested: TNS (parking lights) illumination request signal is received.
• TNS/Headlight On requested: TNS (parking lights) and headlight illumination request signal is received.
|
—
|
|
RLS_TEMP_SEN_FAIL
|
Normal/Fault
|
• Normal: Error signals is not received from the temperature sensor (built into humidity sensor).
• Fault: Error signals is received from the temperature sensor (built into humidity sensor).
|
—
|
|
RLS_UP_LGHT_SEN*10
|
OK/NG
|
• OK: Normal upward brightness can be detected.
• NG: Normal upward brightness cannot be detected.
|
—
|
|
RLS_VOLT_FAIL*10,*11,or*12
|
Normal/Fault
|
• Normal: Power supply voltage of humidity sensor /solar radiation sensor /auto light sensor /rain sensor is normal.
• Fault: Power supply voltage of humidity sensor /solar radiation sensor /auto light sensor /rain sensor is not normal.
|
—
|
|
RLS_WINDOW_TEMP
|
°C, °F
|
Displays windshield temperature.
|
—
|
|
RLS_WIP_REQ*11
|
WiperOFF/WiperOff_duringAutoINT/Single Wipe/SpeedLow/SpeedHigh/Failure
|
• WiperOFF: Wiper operation signal is not received from rain sensor.
• WiperOff_duringAutoINT: Error signals is received from the rain sensor.
• Single Wipe: Signal to operate wiper once is received from rain sensor.
• SpeedLow: Signal to operate wiper at low speed is received from rain sensor.
• SpeedHigh: Signal to operate wiper at high speed is received from rain sensor.
• Failure: Communication with rain sensor is failed.
|
—
|
|
RSRL_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Rear side radar sensor (LH) is not equipped.
• Node Attached and Communicate correctly: Rear side radar sensor (LH) is equipped, communication with rear side radar sensor (LH) is normal.
• NodeAttached but Not Communicate correctly: Rear side radar sensor (LH) is equipped, but communication with rear side radar sensor (LH) is not normal.
|
—
|
|
RSRR_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Rear side radar sensor (RH) is not equipped.
• Node Attached and Communicate correctly: Rear side radar sensor (RH) is equipped, communication with rear side radar sensor (RH) is normal.
• NodeAttached but Not Communicate correctly: Rear side radar sensor (RH) is equipped, but communication with rear side radar sensor (RH) is not normal.
|
—
|
|
S_BELT_LED_OFF_C/R
|
Off/On
|
• Off: Rear seat belt (center) warning light (red) is not illuminated.
• On: Rear seat belt (center) warning light (red) is illuminated.
|
—
|
|
S_BELT_LED_OFF_L/R
|
Off/On
|
• Off: Rear seat belt (LH) warning light (red) is not illuminated.
• On: Rear seat belt (LH) warning light (red) is illuminated.
|
—
|
|
S_BELT_LED_OFF_R/R
|
Off/On
|
• Off: Rear seat belt (RH) warning light (red) is not illuminated.
• On: Rear seat belt (RH) warning light (red) is illuminated.
|
—
|
|
S_BELT_LED_ON_C/R
|
Off/On
|
• Off: Rear seat belt (center) warning light (green) is not illuminated.
• On: Rear seat belt (center) warning light (green) is illuminated.
|
—
|
|
S_BELT_LED_ON_L/R
|
Off/On
|
• Off: Rear seat belt (LH) warning light (green) is not illuminated.
• On: Rear seat belt (LH) warning light (green) is illuminated.
|
—
|
|
S_BELT_LED_ON_R/R
|
Off/On
|
• Off: Rear seat belt (RH) warning light (green) is not illuminated.
• On: Rear seat belt (RH) warning light (green) is illuminated.
|
—
|
|
S_BELT_LED_P
|
Off/On
|
• Off: Passenger seat belt warning light is not illuminated.
• On: Passenger seat belt warning light is illuminated.
|
—
|
|
S_BELT_STAT
|
Vaild/Unknown
|
• Vaild: All rear seat belt warning light signals are normal.
• Unknown: There is a rear seat belt warning light signal error.
|
—
|
|
S_BELT_STAT_C/3RD
|
|
||
|
S_BELT_STAT_C/R
|
RearCenter belt not used (Close)/RearCenter belt used (Open)
|
• RearCenter belt not used(Close): Rear center seat belt is not fastened.
• RearCenter belt used(Open): Rear center seat belt is fastened.
|
—
|
|
S_BELT_STAT_L/3RD
|
|
||
|
S_BELT_STAT_L/R
|
RL belt not used(Close)/RL belt used(Open)
|
• RL belt not used(Close): Rear left seat belt is not fastened.
• RL belt used(Open): Rear left seat belt is fastened.
|
—
|
|
S_BELT_STAT_R/3RD
|
|
||
|
S_BELT_STAT_R/R
|
RR belt not used(Close)/RR belt not used(Open)
|
• RR belt not used(Close): Rear right seat belt is not fastened.
• RR belt used(Open): Rear right seat belt is fastened.
|
—
|
|
S_BELT_WRNG_D
|
driver belt not used/driver belt used/fault(hole IC switch)/resrve(mech switch)
|
• driver belt not used: Driver seat belt is not fastened.
• driver belt used: Driver seat belt is fastened.
• fault(hole IC switch)/resrve(mech switch): Driver seat belt has a malfunction.
|
—
|
|
S_BELT_WRNG_P
|
driver belt not used/driver belt used/fault(hole IC switch)/resrve(mech switch)
|
• driver belt not used: Passenger seat belt is not fastened.
• driver belt used: Passenger seat belt is fastened.
• fault(hole IC switch)/resrve(mech switch): Passenger seat belt has a malfunction.
|
—
|
|
SAS_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Steering angle sensor is not equipped.
• Node Attached and Communicate correctly: Steering angle sensor is equipped, communication with steering angle sensor is normal.
• NodeAttached but Not Communicate correctly: Steering angle sensor is equipped, but communication with steering angle sensor is not normal.
|
—
|
|
SCR_HZRD_REQ
|
Off/On
|
• Off: Secondary collision reduction hazard warning light is not operated.
• On: Secondary collision reduction hazard warning light is operated.
|
—
|
|
SEAT_LETER_ILLMI
|
Off/On
|
• Off: Passenger air bag deactivation (PAD) lettering illumination is not illuminated.
• On: Passenger air bag deactivation (PAD) lettering illumination is illuminated.
|
—
|
|
SEAT_OCS_C/R
|
|
||
|
SEAT_OCS_L/R
|
|
||
|
SEAT_OCS_R/R
|
|
||
|
SEAT_OCS_STAT
|
|
||
|
SHIFT
|
between 2 positions/P/R/N/D/S(2)/L(1)
|
• between 2 positions: Selector lever is between two positions.
• P: Selector lever is in P position.
• R: Selector lever is in R position.
• N: Selector lever is in N position.
• D: Selector lever is in D position.
• S(2): Selector lever is in D position 2nd gear.
• L(1): Selector lever is in D position 1st gear.
|
—
|
|
SLAM_LCK
|
Off/On
|
• On: With all of the following conditions met, lock knob on door equipped with door lock-link switch is locked and all doors are closed.
• Off: Conditions other than above
|
—
|
|
SPARE_KEY_STAT
|
Off/On
|
• Off: There is no spare key.
• On: There is spare key.
|
—
|
|
SSB_1
|
Off/On
|
• Off: Push button start switch 1 is off.
• On: Push button start switch 1 is on.
|
—
|
|
SSB_2
|
Off/On
|
• Off: Push button start switch 2 is off.
• On: Push button start switch 2 is on.
|
—
|
|
SSB_AMBER_REQ
|
Off/On
|
• Off: Push button start indicator light (amber) is turned off.
• On: Push button start indicator light (amber) is illuminated.
|
—
|
|
SSB_GREEN_REQ
|
Off/On
|
• Off: Push button start indicator light (green) is turned off.
• On: Push button start indicator light (green) is illuminated.
|
—
|
|
SSB_ILLMI_REQ
|
Off/On
|
• Off: START/STOP/ENGINE indicator light is turned off.
• On: START/STOP/ENGINE indicator light is illuminated.
|
—
|
|
SSU_RES_NUM
|
0/1/2/3
|
|
—
|
|
SSU_RES_STAT
|
Disable/Enable
|
|
—
|
|
STR_ANG
|
° (deg)
|
Displays steering angle signal (absolute angle)
• Steering wheel in neutral position: Near 0 degrees
• Steering wheel turned to left: Changes from 0 degrees to positive
• Steering wheel turned to right: Changes from 0 degrees to negative
|
—
|
|
STR_COLM_LCK_CTRL
|
Off/On
|
• Off: Steering lock is not operated.
• On: Steering lock is operated.
|
—
|
|
STR_COLM_LCK_GND
|
Off/On
|
• Off: Steering lock is not operated.
• On: Steering lock is operated.
|
—
|
|
STR_COLM_LCK_POWER
|
Off/On
|
• Off: Power is not supplied to steering lock.
• On: Power is supplied to steering lock.
|
—
|
|
STR_COLM_LCK_STAT
|
Locked/Failed 1/Failed 2/Unlocked/Undefined
|
• Locked: Steering is locked.
• Failed 1: Steering lock/unlock is failed.
• Failed 2: Steering lock/unlock is failed.
• Unlocked: Steering is not locked.
• Undefined: Steering lock condition is not determined.
|
—
|
|
STR_COLM_LCK_SW
|
Off/On
|
• Off: Steering lock unlock/lock switch is off.
• On: Steering lock unlock/lock switch is on.
|
—
|
|
STR_COLM_LCK_SW_MEMORY
|
Off/On
|
• Off: Memory value of steering lock unlock/lock switch is not unlocked.
• On: Memory value of steering lock unlock/lock switch is unlocked.
|
—
|
|
STR_COLM_ULCK_SW
|
Not Unlock/Unlock
|
• Not Unlock: Steering lock unlock switch is off.
• Unlock: Steering lock unlock switch is on.
|
—
|
|
STR_COLM_ULCK_SW_MEMORY
|
Not Unlock/Unlock
|
• Not Unlock: Memory value of steering lock unlock switch is not unlocked.
• Unlock: Memory value of steering lock unlock switch is unlocked.
|
—
|
|
STR_HEAT_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Heated steering wheel control unit is not equipped.
• Node Attached and Communicate correctly: Heated steering wheel control unit is equipped, communication with heated steering wheel control unit is normal.
• NodeAttached but Not Communicate correctly: Heated steering wheel control unit is equipped, but communication with heated steering wheel control unit is not normal.
|
—
|
|
SUPER_LCK_ALL*13
|
Off/On
|
• Off: Double locking function (With double locking) is not operated.
• On: Double locking function (With double locking) is operated.
|
2J, 2L
|
|
T/LGT_LCK_SW*18
|
Off/On
|
• Off: Door lock switch (liftgate) is off.
• On: Door lock switch (liftgate) is on.
|
4I
|
|
T/LGT_SW
|
Close/Open
|
• Close: Liftgate is closed.
• Open: Liftgate is open.
|
2J, 2L
|
|
T/LGT_ULCK
|
Off/On
|
• Off: Body control module (BCM) does not operate the liftgate to unlock.
• On: Body control module (BCM) operates the liftgate to unlock.
|
2J, 2L
|
|
TCM_NETWORK*1
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: TCM is not equipped.
• Node Attached and Communicate correctly: TCM is equipped, communication with TCM is normal.
• NodeAttached but Not Communicate correctly: TCM is equipped, but communication with TCM is not normal.
|
—
|
|
TCM_PT2_NETWORK*1
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: TCM is not equipped.
• Node Attached and Communicate correctly: TCM is equipped, communication via CAN BUS No.2 with TCM is normal.
• NodeAttached but Not Communicate correctly: TCM is equipped, but communication via CAN BUS No.2 with TCM is not normal.
|
—
|
|
TCU_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
Except Chinese specs.
• Node is not attached on Vehicle: Emergency call unit is not equipped.
• Node Attached and Communicate correctly: Emergency call unit is equipped, communication with emergency call unit is normal.
• NodeAttached but Not Communicate correctly: Emergency call unit is equipped, but communication with emergency call unit is not normal.
Chinese specs.
• Node is not attached on Vehicle: Mazda EMERGENCY ASSISTANCE control module is not equipped.
• Node Attached and Communicate correctly: Mazda EMERGENCY ASSISTANCE control module is equipped, communication with Mazda EMERGENCY ASSISTANCE control module is normal.
• NodeAttached but Not Communicate correctly: Mazda EMERGENCY ASSISTANCE control module is equipped, but communication with Mazda EMERGENCY ASSISTANCE control module is not normal.
|
—
|
|
TEMP_LH_ACTAT_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Driver-side air mix actuator is not equipped.
• Node Attached and Communicate correctly: Driver-side air mix actuator is equipped, communication with driver-side air mix actuator is normal.
• NodeAttached but Not Communicate correctly: Driver-side air mix actuator is equipped, but communication with driver-side air mix actuator is not normal.
|
—
|
|
TEMP_RH_ACTAT_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Passenger-side air mix actuator is not equipped.
• Node Attached and Communicate correctly: Passenger-side air mix actuator is equipped, communication with passenger-side air mix actuator is normal.
• NodeAttached but Not Communicate correctly: Passenger-side air mix actuator is equipped, but communication with passenger-side air mix actuator is not normal.
|
—
|
|
TGT_VERIFY
|
Error/OK
|
Displays immobilizer system condition.
|
—
|
|
TIRE_PRES_L/F
|
kPa
|
Displays tire pressure (wheel unit (LF))
|
—
|
|
TIRE_PRES_L/R
|
kPa
|
Displays tire pressure (wheel unit (LR))
|
—
|
|
TIRE_PRES_R/F
|
kPa
|
Displays tire pressure (wheel unit (RF))
|
—
|
|
TIRE_PRES_R/R
|
kPa
|
Displays tire pressure (wheel unit (RR))
|
—
|
|
TIRE_TEMP_L/F
|
°C, °F
|
Displays tire temperature (wheel unit (LF))
|
—
|
|
TIRE_TEMP_L/R
|
°C, °F
|
Displays tire temperature (wheel unit (LR))
|
—
|
|
TIRE_TEMP_R/F
|
°C, °F
|
Displays tire temperature (wheel unit (RF))
|
—
|
|
TIRE_TEMP_R/R
|
°C, °F
|
Displays tire temperature (wheel unit (RR))
|
—
|
|
TMTR_NUM
|
0/1/2/3/4/5/6
|
Displays registration number of the remote transmitter
|
—
|
|
TNS_REQ
|
Off/On
|
• Off: Body control module (BCM) does not operate the TNS (parking lights) on.
• On: Body control module (BCM) operates the TNS (parking lights) on.
|
—
|
|
TNS_SW
|
Off/On
|
• Off: Light switch TNS (parking lights) signal is not received.
• On: Light switch TNS (parking lights) signal is received.
|
—
|
|
TOPOLOGY_ID
|
—
|
Displays topological ID
|
—
|
|
TOTAL_DIST
|
km, ft, mi
|
Displays total traveled distance
|
—
|
|
TPMS_FAIL
|
Default/Zero Learnt/One Learnt/Two Learnt/Three Learnt/ABS Error/Maximum speed exceeded/Location not determined/Locate data issue
|
Displays reason why tire position recognition failed.
|
—
|
|
TPMS_MODE_L/F
|
Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode
|
Displays wheel unit (LF) mode
|
—
|
|
TPMS_MODE_L/R
|
Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode
|
Displays wheel unit (LR) mode
|
—
|
|
TPMS_MODE_R/F
|
Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode
|
Displays wheel unit (RF) mode
|
—
|
|
TPMS_MODE_R/R
|
Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode
|
Displays wheel unit (RR) mode
|
—
|
|
TUNER_NETWORK*14
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Remote tuner (RT) is not equipped.
• Node Attached and Communicate correctly: Remote tuner (RT) is equipped, communication with remote tuner (RT) is normal.
• NodeAttached but Not Communicate correctly: Remote tuner (RT) is equipped, but communication with remote tuner (RT) is not normal.
|
—
|
|
TURN_L
|
Off/On
|
• Off: Turn switch LH signal is not sent from body control module (BCM).
• On: Turn switch LH signal is sent from body control module (BCM).
|
—
|
|
TURN_L_INTERIOR
|
Off/On
|
• Off: Turn signal (LH) or hazard warning indicator signal is not sent from body control module (BCM).
• On: Turn signal (LH) or hazard warning indicator signal is sent from body control module (BCM).
|
—
|
|
TURN_R
|
Off/On
|
• Off: Turn switch RH signal is not sent from body control module (BCM).
• On: Turn switch RH signal is sent from body control module (BCM).
|
—
|
|
TURN_R_INTERIOR
|
Off/On
|
• Off: Turn signal (RH) or hazard warning indicator signal is not sent from body control module (BCM).
• On: Turn signal (RH) or hazard warning indicator signal is sent from body control module (BCM).
|
—
|
|
TURN_SW
|
Turn Off/Turn Right ON/Turn Left ON/Unknown
|
• Turn Off: Turn switch is in OFF position.
• Turn Right ON: Turn switch is in RH position.
• Turn Left ON: Turn switch is in LH position.
• Unknown: Turn switch position is not determined.
|
—
|
|
USBHUB_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Auxiliary jack/USB port/sd card slot hub is not equipped.
• Node Attached and Communicate correctly: Auxiliary jack/USB port/sd card slot hub is equipped, communication with auxiliary jack/USB port/sd card slot hub is normal.
• NodeAttached but Not Communicate correctly: Auxiliary jack/USB port/sd card slot hub is equipped, but communication with auxiliary jack/USB port/sd card slot hub is not normal.
|
—
|
|
VCM_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Vehicle control module (VCM) is not equipped.
• Node Attached and Communicate correctly: Vehicle control module (VCM) is equipped, communication with vehicle control module (VCM) is normal.
• NodeAttached but Not Communicate correctly: Vehicle control module (VCM) is equipped, but communication with vehicle control module (VCM) is not normal.
|
—
|
|
VDT_MODE*14
|
Normal Mode/Manual Trigger Mode/i-ActivSense Analysis Mode/Reject Mode
|
• Normal Mode: Vehicle is in normal mode.
• Manual Trigger Mode: Vehicle is in driving data collecting mode.
• i-ActivSense Analysis Mode: Vehicle is in i-ACTIVSENSE data collecting mode.
• Reject Mode: Restricted remote operation and data transfer.
|
—
|
|
VMC_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: 360°view monitor control module/parking assist unit (optical) is not equipped.
• Node Attached and Communicate correctly: 360°view monitor control module/parking assist unit (optical) is equipped, communication with 360°view monitor control module/parking assist unit (optical) is normal.
• NodeAttached but Not Communicate correctly: 360°view monitor control module/parking assist unit (optical) is equipped, but communication with 360°view monitor control module/parking assist unit (optical) is not normal.
|
—
|
|
VPWR_ACC
|
V
|
Displays voltage at body control module (BCM) terminal 2AE (ACC power supply)
|
2AE
|
|
VPWR_CBCM
|
V
|
Displays power supply voltage of body control module (BCM)
|
—
|
|
VPWR_ESCL
|
V
|
Displays voltage at body control module (BCM) terminal 4W (power supply)
|
4W
|
|
VPWR_IG
|
V
|
Displays voltage at body control module (BCM) terminal 2AF (ignition power supply)
|
2AF
|
|
VPWR_LIMP_HOME
|
V
|
Displays voltage at body control module (BCM) terminal 1B (power supply)
|
1B
|
|
VPWR_ROOM
|
V
|
Displays voltage at body control module (BCM) terminal 1D (power supply)
|
1D
|
|
WASH_MOTOR_STAT
|
Off/Washer_Motor_L/Washer_Motor_R
|
• Off: Windshield washer motor relay and rear washer motor relay are off.
• Washer_Motor_L: Windshield washer motor relay is on.
• Washer_Motor_R: Rear washer motor relay is on.
|
—
|
|
WIP_NETWORK
|
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
|
• Node is not attached on Vehicle: Windshield wiper motor is not equipped.
• Node Attached and Communicate correctly: Windshield wiper motor is equipped, communication with windshield wiper motor is normal.
• NodeAttached but Not Communicate correctly: Windshield wiper motor is equipped, but communication with windshield wiper motor is not normal.
|
—
|