Home

Mazdamanuals.com

SNAPSHOT DATA TABLE [INTEGRATED STARTER GENERATOR (ISG)]

SNAPSHOT DATA TABLE [INTEGRATED STARTER GENERATOR (ISG)]

id140202100500

—: Not applicable

Item

Unit/Condition

Definition
ALT_MODE
—
•  Displays the integrated starter generator (ISG) power generation mode.
AMB_TEMP
°C, °F
•  Ambient air temperature
APP
%
•  Displays accelerator pedal opening angle
BATT_TERMINAL_CUR_EST
A
•  Displays the estimated current input to integrated starter generator (ISG) terminal 2A.
BATT_TERMINAL_VOLT
V
•  Displays the voltage input to integrated starter generator (ISG) terminal 2A.
BATT_TERMINAL_VOLT_A/D
V
•  Displays the terminal 2A voltage supplied to the input voltage converter in the integrated starter generator (ISG).
BATT_TERMINAL_VOLT_GD
V
•  Displays the terminal 2A voltage supplied to the drive circuit in the integrated starter generator (ISG).
BATT_TERMINAL_VOLT_REQ
V
•  Displays the target value of the terminal 2A voltage input from the PCM.
B-ISG_RPM
r/min
•  Displays the rotor rotation speed.
BRK_SW
—
•  Displays the brake pedal depression status.
CTRL_MODE
Standby / Torque Control / Voltage Control / System Waiting / System Stopping / System Wakeup / Braking
•  Displays the control status of the integrated starter generator (ISG).
―  Standby: During control standby
―  Torque Control: During power generation torque/drive torque control
―  Voltage Control: During voltage control
―  System Waiting: Activation of Mazda M Hybrid on standby
―  System Stopping: Ends activation of integrated starter generator (ISG)
―  System Wakeup: Starts activation of integrated starter generator (ISG)
―  Braking: During braking torque control
CTRL_MODE_REQ
Standby / Torque Control / Voltage Control / System Waiting / System Stopping / System Wakeup / Braking
•  Displays the control request signal of the integrated starter generator (ISG) input from the PCM.
―  Standby: During control standby
―  Torque Control: During power generation torque/drive torque control
―  Voltage Control: During voltage control
―  System Waiting: Activation of Mazda M Hybrid on standby
―  System Stopping: Ends activation of integrated starter generator (ISG)
―  System Wakeup: Starts activation of integrated starter generator (ISG)
―  Braking: During braking torque control
CTRL_TEMP
°C, °F
•  Displays the temperature detected by the control board temperature sensor in the integrated starter generator (ISG).
CTRL_TEMP_A/D
V
•  Displays the voltage conversion value for the control board temperature sensor temperature in the integrated starter generator (ISG) supplied to the input voltage converter in the integrated starter generator (ISG).
ECT
°C, °F
•  Engine coolant temperature input from ECT sensor No.1
ENG_RPM
rpm
•  Displays engine speed
ENG_RUN_TIME
Second
•  Time from engine start
FIELD_COIL_TEMP_EST
—
•  Displays the field coil temperature (estimated) of the integrated starter generator (ISG).
FIELD_CUR
A
•  Displays the field coil current of the integrated starter generator (ISG).
FIELD_CUR_A/D
V
•  Displays the field coil current converted to voltage which is supplied to the input voltage converter in the integrated starter generator (ISG).
FIELD_CUR_OFFSET_A/D
V
•  Displays the measurement difference error value of the field coil current converted to voltage which is supplied to the input voltage converter in the integrated starter generator (ISG).
FIELD_DUTY
%
•  Displays the field coil control duty value.
GLOBAL_REAL_TIME
min
•  Displays the cumulative, total elapsed time since the vehicle was shipped.
IG_CYCLE_COUNT
times
•  Displays the number of times power is supplied from the IG1 relay.
IG_ON_TIMER
min
•  Displays the elapsed time since the ignition was switched ON (engine off).
IG_SIG
—
SKYACTIV-G
•  Displays the power supply status from the electric variable valve timing relay.
SKYACTIV-X
•  Displays the power supply status from the exhaust electrical variable valve timing relay.
IG_SIG_CAN
—
•  Displays the power supply status from the IG1 relay input via CAN communication.
MOSFET_TEMP
°C, °F
•  Displays the 6-phase FET temperature in the integrated starter generator (ISG).
MPU_TEMP
°C, °F
•  Displays the microcomputer temperature in the integrated starter generator (ISG).
POWER_MODE
OFF/ACC/ON/CRANK
•  Displays the vehicle status.
―  OFF:Ignition is switched to OFF
―  ACC:Ignition is switched to ACC
―  ON:Ignition is switched to ON (engine off)
―  CRANK:During engine cranking
SHIFT_POS
Parking/
Reverse/
Neutral/
between 2 position/
Forward Drive 1/
Forward Drive 2/
Forward Drive 3/
Forward Drive 4/
Forward Drive 5/
Forward Drive 6/
Forward Drive 7/
Parking/Neutral/
Invalid
•  Displays selector lever position
―  Parking: P position
―  Reverse: R position
―  Neutral: N position
―  Between 2 position: Between 2 shift positions
―  Forward Drive 1: 1st gear
―  Forward Drive 2: 2nd gear
―  Forward Drive 3: 3rd gear
―  Forward Drive 4: 4th gear
―  Forward Drive 5: 5th gear
―  Forward Drive 6: 6th gear
―  Forward Drive 7: —
―  Parking/Neutral: Neutral position (MTX)
―  Invalid: Signal invalid
TOTAL_DIST
km, ft, mi
•  Total distance
TRQ_EST
N·m
•  Displays the output torque request value of the integrated starter generator (ISG).
TRQ_RATE_LIM_DECREASE
N·m/s
•  Displays the speed at which the power generation torque decreases.
TRQ_RATE_LIM_INCREASE
N·m/s
•  Displays the speed at which the power generation torque increases.
TRQ_REQ
N·m
•  Displays the output torque request value input from the PCM.
U_PHASE_CUR_A/D
V
•  Displays the value of the U-phase current converted to voltage which is supplied to the input voltage converter in the integrated starter generator (ISG).
U_PHASE_TEMP_A/D
V
•  Displays the voltage of the U-phase FET temperature which is supplied to the input voltage converter in the integrated starter generator (ISG).
UNDER_VOLT_REQ
—
•  Displays the terminal 2A low voltage error signal of the integrated starter generator (ISG) input via CAN communication.
V_PHASE_CUR_A/D
V
•  Displays the value of the V-phase current converted to voltage which is supplied to the input voltage converter in the integrated starter generator (ISG).
V_PHASE_TEMP_A/D
V
•  Displays the voltage of the V-phase FET temperature which is supplied to the input voltage converter in the integrated starter generator (ISG).
VPWR
V
•  Displays the integrated starter generator (ISG) power supply voltage.
VPWR_CBCM
V
•  Body control module (BCM) power supply voltage.
VSS
KPH, MPH
•  Displays vehicle speed
W_PHASE_CUR_A/D
V
•  Displays the value of the W-phase current converted to voltage which is supplied to the input voltage converter in the integrated starter generator (ISG).
W_PHASE_TEMP_A/D
V
•  Displays the voltage of the W-phase FET temperature which is supplied to the input voltage converter in the integrated starter generator (ISG).
X_PHASE_CUR_A/D
V
•  Displays the value of the X-phase current converted to voltage which is supplied to the input voltage converter in the integrated starter generator (ISG).
X_PHASE_TEMP_A/D
V
•  Displays the voltage of the X-phase FET temperature which is supplied to the input voltage converter in the integrated starter generator (ISG).
Y_PHASE_CUR_A/D
V
•  Displays the value of the Y-phase current converted to voltage which is supplied to the input voltage converter in the integrated starter generator (ISG).
Y_PHASE_TEMP_A/D
V
•  Displays the voltage of the Y-phase FET temperature which is supplied to the input voltage converter in the integrated starter generator (ISG).
Z_PHASE_CUR_A/D
V
•  Displays the value of the Z-phase current converted to voltage which is supplied to the input voltage converter in the integrated starter generator (ISG).
Z_PHASE_TEMP_A/D
V
•  Displays the voltage of the Z-phase FET temperature which is supplied to the input voltage converter in the integrated starter generator (ISG).