Home

Mazdamanuals.com

SNAPSHOT DATA TABLE [Mazda M Hybrid BATTERY]

id140204100500

—: Not applicable

Item	Unit/Condition	Definition
AMB_TEMP	°C, °F	• Displays the ambient temperature.
BATT_PACK_CUR	A	• Displays the input/output current of the Mazda M Hybrid battery.
BATT_PACK_RLY	V	• Displays the output terminal voltage of the Mazda M Hybrid battery.
BATT_PACK_U	V	• Displays the total voltage for the Mazda M Hybrid battery.
BATT_PACK_VOLT	V	• Displays the total cell voltage for the Mazda M Hybrid battery.
BATT_PRECHARGE_REQ	CLOSE/OPEN	• Displays the operation request status of the pre-charge FET. ― CLOSE: During PCM pre-charge FET CLOSE request ― OPEN: During PCM pre-charge FET OPEN request
BATT_SOC	%	• Displays the battery charge condition.
BATT_TEMP_1	°C, °F	• Displays the Mazda M Hybrid battery temperature detected by the temperature sensor (No.1) in the Mazda M Hybrid battery.
BATT_TEMP_2	°C, °F	• Displays the Mazda M Hybrid battery temperature detected by the temperature sensor (No.2) in the Mazda M Hybrid battery.
BATT_VOLT	V	• Displays the battery voltage.
BECM_STAT	OFF / INITIAL / STANDBY / PRECHARGE / READY / DISCHARGE / POWER SUSTAIN / FAIL	• Displays the operation status of the Mazda M Hybrid battery. ― OFF: Not operating ― INITIAL: Initializing ― STANDBY: On operation standby ― PRECHARGE: Receives contactor CLOSE request signal from another module while on standby ― READY: Charging enabled ― DISCHARGE: During contactor off ― POWER SUSTAIN: During Mazda M Hybrid battery operation interruption ― FAIL: Mazda M Hybrid battery malfunction detected
CELL_BALANCE_REQ	DISABLE/ENABLE	• Displays the operation permit status for the function which equalizes the charged capacity of the Mazda M Hybrid battery. ― DISABLE: Inhibit ― ENABLE: Permit
CELL_BALANCE_STAT	Off/Running	• Displays the operation status for the function which equalizes the charged capacity of the Mazda M Hybrid battery. ― Off: Stopped ― Running: Operating
CELL_VOLT_1	V	• Displays the voltage of the Mazda M Hybrid battery cell (No.1).
CELL_VOLT_2	V	• Displays the voltage of the Mazda M Hybrid battery cell (No.2).
CELL_VOLT_3	V	• Displays the voltage of the Mazda M Hybrid battery cell (No.3).
CELL_VOLT_4	V	• Displays the voltage of the Mazda M Hybrid battery cell (No.4).
CELL_VOLT_5	V	• Displays the voltage of the Mazda M Hybrid battery cell (No.5).
CELL_VOLT_6	V	• Displays the voltage of the Mazda M Hybrid battery cell (No.6).
CELL_VOLT_7	V	• Displays the voltage of the Mazda M Hybrid battery cell (No.7).
CELL_VOLT_8	V	• Displays the voltage of the Mazda M Hybrid battery cell (No.8).
CELL_VOLT_9	V	• Displays the voltage of the Mazda M Hybrid battery cell (No.9).
CONTACTOR_REQ	OPEN/CLOSE	• Displays the contactor drive request signal which the CPU in the Mazda M Hybrid battery commands. ― OPEN: During CPU contactor off request ― CLOSE: During CPU contactor on request
CONTACTOR_STAT	CLOSE / OPEN / INITIAL / UNKNOWN	• Displays the operation status of the contactor for the Mazda M Hybrid battery. ― CLOSE: Contactor on ― OPEN: Contactor off ― INITIAL: Initializing ― UNKNOWN: Detection not possible
ENG_RPM	rpm	• Displays the engine speed.
ENG_RUN_TIME	Second	• Displays the elapsed time since the engine was started.
GLOBAL_REAL_TIME	min	• Displays the cumulative, total elapsed time since the vehicle was shipped.
IG_ON_TIMER	min	• Displays the elapsed time since the ignition was switched ON (engine off).
POWER_MODE	OFF / ACC / ON / CRANK	• Displays the vehicle status. ― OFF: Ignition is switched to OFF ― ACC: Ignition is switched to ACC ― ON: Ignition is switched ON (engine off) ― CRANK: During engine cranking
PRECHARGE_FET_TEMP	°C, °F	• Displays the FET temperature in the Mazda M Hybrid battery.
TOTAL_DIST	km, ft, mi	• Displays the total driving distance.
VEH_POWER_CONDITION	POWER OFF/IG SW On	• Vehicle conditions ― POWER OFF: Ignition switched OFF ― IG SW On: Ignition switched ON
VPWR_CBCM	V	• Body control module (BCM) power supply voltage.
VSS	KPH, MPH	• Displays the vehicle speed.