Home

Mazdamanuals.com

REAR SIDE RADAR SENSOR INSPECTION

id152000014900

1. Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(E)])

2. Remove the rear side radar sensor. (See REAR SIDE RADAR SENSOR REMOVAL/INSTALLATION.)

3. Connect the rear side radar sensor connector.

4. Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(E)])

5. Verify that the voltages of each of the terminals are as indicated in the terminal voltage table (reference).

• If the voltage is not as specified in the terminal voltage table (reference), inspect the parts under Inspection item(s) and related wiring harnesses.

― If the system does not operate normally even though the inspection items are normal, replace the rear side radar sensor. (See REAR SIDE RADAR SENSOR REMOVAL/INSTALLATION.)

Terminal Voltage Table (Reference)

Rear side radar sensor (LH)

am3zzw00027438

Terminal

Signal name

Connected to

Measurement conditions

Voltage (V)

Inspection item(s)

A

PRI_CAN_H

Front side radar sensor (RH)

Because this terminal is for communication, determination using terminal voltage inspection is not possible.

B

PRI_CAN_L

Front side radar sensor (RH)

Because this terminal is for communication, determination using terminal voltage inspection is not possible.

C

—

—

—

—

—

D

—

—

—

—

—

E

—

—

—

—

—

F

—

—

—

—

—

G

—

—

—

—

—

H

—

—

—

—

—

I

Power position (IG1)

IG1 relay

Ignition switched ON (engine off or on)

V_B

•  F54 15A fuse

•  IG1 relay

•  Related wiring harness

Ignition switched off or ACC

1.0 or less

J

Ground

Body ground

Under any condition

Approx. 0

•  GND point

•  Related wiring harness

Terminal	Signal name	Connected to	Measurement conditions	Voltage (V)	Inspection item(s)
A	PRI_CAN_H	Front side radar sensor (RH)	Because this terminal is for communication, determination using terminal voltage inspection is not possible.
B	PRI_CAN_L	Front side radar sensor (RH)	Because this terminal is for communication, determination using terminal voltage inspection is not possible.
C	—	—	—	—	—
D	—	—	—	—	—
E	—	—	—	—	—
F	—	—	—	—	—
G	—	—	—	—	—
H	—	—	—	—	—
I	Power position (IG1)	IG1 relay	Ignition switched ON (engine off or on)	V_B	• F54 15A fuse • IG1 relay • Related wiring harness
Ignition switched off or ACC	1.0 or less
J	Ground	Body ground	Under any condition	Approx. 0	• GND point • Related wiring harness

Rear side radar sensor (RH)

am3zzw00027437

Terminal

Signal name

Connected to

Measurement conditions

Voltage (V)

Inspection item(s)

A

PRI_CAN_H

Front side radar sensor (RH)

Because this terminal is for communication, determination using terminal voltage inspection is not possible.

B

PRI_CAN_L

Front side radar sensor (RH)

Because this terminal is for communication, determination using terminal voltage inspection is not possible.

C

ADAS_CAN_H

Data link connector-2

Because this terminal is for communication, determination using terminal voltage inspection is not possible.

D

ADAS_CAN_L

Data link connector-2

Because this terminal is for communication, determination using terminal voltage inspection is not possible.

E

—

—

—

—

—

F

—

—

—

—

—

G

—

—

—

—

—

H

—

—

—

—

—

I

Power position (IG1)

IG1 relay

Ignition switched ON (engine off or on)

V_B

•  F54 15A fuse

•  IG1 relay

•  Related wiring harness

Ignition switched off or ACC

1.0 or less

J

Ground

Body ground

Under any condition

Approx. 0

•  GND point

•  Related wiring harness