Diagnostic procedure
|
STEP
|
INSPECTION
|
ACTION
|
|
|---|---|---|---|
|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
|
||
|
2
|
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
• Verify related service repair information availability.
• Is any related repair information available?
|
Yes
|
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to the next step.
|
|
No
|
Go to the next step.
|
||
|
3
|
VERIFY RELATED PENDING AND STORED DTC
• Turn the engine switch off, then to the ON position (Engine off).
• Verify pending and stored DTCs using the WDS or equivalent.
• Are other DTCs present?
|
Yes
|
Go to the appropriate DTC troubleshooting procedures.
|
|
No
|
Go to the next step.
|
||
|
4
|
IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA
• Is DTC P0134 on FREEZE FRAME DATA?
|
Yes
|
Go to the next step.
|
|
No
|
Go to troubleshooting procedures for DTC on FREEZE FRAME DATA.
|
||
|
5
|
VERIFY CURRENT INPUT SIGNAL STATUS
• Warm up engine.
• Access O2S11 PID using the WDS or equivalent.
• Verify PID while racing engine in PARK or NEUTRAL.
• Is PID normal?
- Less than 1 mA when suddenly depressing accelerator pedal (rich condition) - More than 1 mA just after releasing the accelerator pedal (lean condition) |
Yes
|
Go to step 10.
|
|
No
|
Go to the next step.
|
||
|
6
|
INSPECT INSTALLATION OF A/F SENSOR
• Inspect if the A/F sensor is loosely installed.
• Is the sensor installed securely?
|
Yes
|
Go to the next step.
|
|
No
|
Install sensor securely, then go to Step 12.
|
||
|
7
|
INSPECT GAS LEAKAGE FROM EXHAUST SYSTEM
• Visually inspect if there is any gas leakage between the exhaust manifold and A/F sensor.
• Is there gas leakage?
|
Yes
|
Repair or replace any malfunctioning exhaust part, then go to Step 12.
|
|
No
|
Go to the next step.
|
||
|
8
|
INSPECT A/F SENSOR SIGNAL CIRCUIT FOR OPEN CIRCUIT
• Inspect for continuity between the A/F sensor terminal A (wiring harness-side) to the PCM terminal 93 (wiring harness-side).
• Is there continuity?
|
Yes
|
Go to the next step
|
|
No
|
Repair or replace the wiring harness for a possible open circuit, then go to Step 12.
|
||
|
9
|
INSPECT A/F SENSOR SIGNAL CIRCUIT FOR SHORT TO GROUND
• Inspect for continuity between the A/F sensor terminal A (wiring harness-side) to body ground.
• Is there continuity?
|
Yes
|
Repair or replace the wiring harness for a possible short to ground, then go to Step 12.
|
|
No
|
Go to the next step.
|
||
|
10
|
INSPECT SEALING OF ENGINE COOLANT PASSAGE
• Perform the ENGINE COOLANT LEAKAGE INSPECTION. (See ENGINE COOLANT LEAKAGE INSPECTION [MZR-CD (RF Turbo)].)
• Is there any malfunction?
|
Yes
|
Repair or replace the malfunctioning part according to inspection results, then go to Step 12.
|
|
No
|
Go to the next step.
|
||
|
11
|
INSPECT ENGINE COMPRESSION
• Inspect the engine compression.
• Is it normal?
|
Yes
|
Go to the next step.
|
|
No
|
Perform engine overhaul for repairs, then go to the next step.
|
||
|
12
|
VERIFY TROUBLESHOOTING OF DTC P0134 COMPLETED
• Make sure to reconnect all disconnected connectors.
• Turn the engine switch to the ON position (Engine off).
• Clear the DTC from memory using the WDS or equivalent.
• Perform the Repair Verification Drive Mode.
• Is the PENDING CODE for this DTC present?
|
Yes
|
Replace the PCM, then go to the next step.
|
|
No
|
Go to the next step.
|
||
|
13
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the "After Repair Procedure".
• Are any DTC present?
|
Yes
|
Go to the applicable DTC troubleshooting.
|
|
No
|
Troubleshooting completed.
|
||
