Home

Mazdamanuals.com

 DTC P0336 [MZR-CD (RF Turbo)]

DTC P0336 [MZR-CD (RF Turbo)]

id0102f1831000

DTC P0336

CKP sensor range/performance malfunction

DETECTION CONDITION

• The PCM monitors the input signal from the CKP sensor while the engine is running. If the input signal from the CKP sensor does not correspond with the proper pulse number, the PCM determines CKP sensor performance malfunction.
Diagnostic support note
• The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.
• PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle.
• FREEZE FRAME DATA is available.
• The DTC is stored in the PCM memory.

POSSIBLE CAUSE

• Loose CKP sensor installation bolt
• CKP sensor malfunction
• Connector or terminal malfunction
• Flywheel (pulse wheel) malfunction
• Related wiring harness malfunction
• PCM malfunction

Diagnostic procedure

STEP

INSPECTION

ACTION

1
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has FREEZE FRAME DATA been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
• Verify related Service Information availability.
• Is any related repair information available?
Yes
Perform repair or diagnosis according to the available Service Information.
• If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY CURRENT SIGNAL STATUS: IS CONCERN INTERMITTENT OR CONSTANT?
• Connect the WDS or equivalent to the DLC-2.
• Clear the DTC from the PCM memory using the WDS or equivalent.
• Start the engine.
• Is the PENDING CODE for this DTC present?
Yes
Go to the next step.
No
Intermittent concern exists.
Perform the "INTERMITTENT CONCERN TROUBLESHOOTING".
4
INSPECT FLYWHEEL
• Inspect the flywheel for damage and/or cracks.
• Is there any malfunction?
Yes
Replace the flywheel, then go to Step 10.
No
Go to the next step.
5
INSPECT CKP SENSOR CONNECTOR FOR POOR CONNECTION
• Turn the engine switch off.
• Inspect for poor connection (such as damaged/pulled-out terminals, corrosion).
• Is there any malfunction?
Yes
Repair or replace the suspected terminal, go to Step 10.
No
Go to the next step.
6
INSPECT CKP SENSOR
• Inspect the CKP sensor.
• Is there any malfunction?
Yes
Replace the CKP sensor, go to Step 10.
No
Go to the next step.
7
VERIFY CKP SENSOR INSTALLATION CONDITION
• Inspect for CKP sensor looseness.
• Is CKP sensor loosen?
Yes
Retighten the CKP sensor installation bolt, then go to Step 10.
No
Go to the next step.
8
INSPECT CKP SENSOR HARNESS
• Inspect the CKP sensor related wiring harness condition (intermittent open or short).
• Are wiring harness conditions normal?
Yes
Go to the next step.
No
Repair the suspected wiring harness, then go to Step 10.
9
INSPECT PCM CONNECTOR FOR POOR CONNECTION
• Turn the engine switch off.
• Inspect for poor connection (such as damaged/pulled-out terminals, corrosion).
• Is there any malfunction?
Yes
Repair or replace the suspected terminal, go to the next step.
No
Go to the next step.
10
VERIFY TROUBLESHOOTING OF DTC P0336 COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the WDS or equivalent.
• Start the engine.
• Is the PENDING CODE for this DTC present?
Yes
Replace the PCM, go to the next step.
No
Go to the next step.
11
VERIFY AFTER REPAIR PROCEDURE
• Perform the Repair Verification Drive Mode.
• Are any DTCs present?
Yes
Go to the applicable DTC inspection.
No
Troubleshooting completed.