NO.3 TRANSMITTER ID CODE CANNOT BE REPROGRAMMED [KEYLESS ENTRY SYSTEM]
id0903d2800800
|
3
|
Transmitter ID code cannot be reprogrammed
|
|
DESCRIPTION
|
• Malfunction in transmitter battery, transmitter, BCM circuit, or keyless receiver circuit.
|
|
POSSIBLE CAUSE
|
• Malfunction in transmitter battery, transmitter, BCM, or keyless receiver.
|
 |
|
Diagnostic procedure
|
STEP |
INSPECTION |
ACTION |
|
|---|---|---|---|
|
1
|
The transmitter operation indicator light (LED) illuminates when any operation using the transmitter is performed.
|
Yes
|
Go to Step 6.
|
|
No
|
Go to the next step.
|
||
|
2
|
• Visually inspect the transmitter battery for the following:
• Is there any malfunction?
|
Yes
|
Battery insertion direction, battery type problem:
• Properly install the battery or replace the battery with a specified one (CR1620), then go to the next step.
Battery terminal malfunction:
• Clean corrosion and soiling or repair the terminal, then go to the next step.
|
|
No
|
Go to Step 4.
|
||
|
3
|
• Does the keyless entry system operate properly?
|
Yes
|
Go to Step 6.
|
|
No
|
Go to the next step.
|
||
|
4
|
• Inspect while the batteries for all of the transmitters are replaced with monitor-use batteries (normal battery).
• For each transmitter, verify that the transmitter operation indicator light (LED) illuminates when a button is operated.
• Does operation indicator light (LED) for each transmitter operate?
|
Yes
|
Go to the next step.
|
|
No
|
If the operation indicator light (LED) does not illuminate, replace the transmitter, then go to Step 12.
|
||
|
5
|
Does operation indicator light (LED) for each transmitter operate?
|
Yes
|
Replace the battery, then go to Step 12.
|
|
No
|
Go to the next step.
|
||
|
6
|
• Did the customer activate the transmitter within operative area (Within 1 m {3 ft} from area around vehicle)?
|
Yes
|
Go to the next step.
|
 |
No
|
The system is normal.
Explain to the customer that the system does not work without the system operative area.
|
|
|
7
|
INSPECT POWER SUPPLY FUSE
• Is the keyless receiver power supply fuse normal?
|
Yes
|
Go to the next step.
|
|
No
|
Install an appropriate amperage fuse, then go to Step 12.
|
||
|
8
|
INSPECT IF MALFUNCTION IS IN WIRING HARNESS (NO CONTINUITY BETWEEN FUSE BLOCK AND KEYLESS RECEIVER) OR ELSEWHERE
• Measure the voltage at the following keyless receiver terminal:
• Is the voltage B+?
|
Yes
|
Go to the next step.
|
|
No
|
Repair the wiring harness between the fuse block and keyless receiver, then go to Step 12.
|
||
|
9
|
INSPECT IF MALFUNCTION IS IN WIRING HARNESS (NO CONTINUITY BETWEEN KEYLESS RECEIVER AND GROUND) OR ELSEWHERE
• Is there continuity between keyless receiver terminal E and ground?
|
Yes
|
Go to the next step.
|
|
No
|
Repair the wiring harness between the keyless receiver and ground, then go to Step 12.
|
||
|
10
|
INSPECT IF MALFUNCTION IS IN WIRING HARNESS (NO CONTINUITY BETWEEN KEYLESS RECEIVER AND BCM) OR ELSEWHERE
• Disconnect the keyless receiver connector and BCM connector.
• Is there continuity between the following terminals?
|
Yes
|
Go to the next step.
|
|
No
|
Repair the wiring harness between the keyless receiver and BCM, then go to Step 12.
|
||
|
11
|
INSPECT IF MALFUNCTION IS IN WIRING HARNESS (NO CONTINUITY BETWEEN KEYLESS RECEIVER AND BCM) OR BCM
• Measure the voltage at BCM terminal C.
• Is the voltage normal?
|
Yes
|
Replace the BCM, then go to the next step.
|
|
No
|
Replace the keyless receiver, then go to the next step.
|
||
|
12
|
REINSPECT MALFUNCTION SYMPTOM AFTER REPAIR
• Does the keyless entry system operate properly?
|
Yes
|
Troubleshooting completed.
Explain repairs to the customer.
|
|
No
|
Reinspect the malfunction symptoms, then repeat from Step 1 if the malfunction recurs.
|
||