Home

Mazdamanuals.com

DTC C0001:01, C0002:01, C0003:01, C0004:01, C0010:01, C0011:01, C0014:01, C0015:01, C0018:01, C0019:01, C001C:01 OR C001D:01 [DSC HU/CM]

DTC C0001:01, C0002:01, C0003:01, C0004:01, C0010:01, C0011:01, C0014:01, C0015:01, C0018:01, C0019:01, C001C:01 OR C001D:01 [DSC HU/CM]


 id040262003200


Outline

System malfunction location

DTC C0001:01

Traction control solenoid valve (LF/RR)

DTC C0002:01

Traction control solenoid valve (RF/LR)

DTC C0003:01

Stability control solenoid valve (LF/RR)

DTC C0004:01

Stability control solenoid valve (RF/LR)

DTC C0010:01

Inlet solenoid valve (LF)

DTC C0011:01

Outlet solenoid valve (LF)

DTC C0014:01

Inlet solenoid valve (RF)

DTC C0015:01

Outlet solenoid valve (RF)

DTC C0018:01

Inlet solenoid valve (LR)

DTC C0019:01

Outlet solenoid valve (LR)

DTC C001C:01

Inlet solenoid valve (RR)

DTC C001D:01

Outlet solenoid valve (RR)

Detection condition
•  Malfunction detected in the DSC HU/CM solenoid valve or internal circuit by the DSC HU/CM on-board diagnostic function
Fail-safe
Refer to “DTC Table” and “Fail-safe Function Malfunction Contents Table”.(See DTC TABLE [DSC HU/CM (E)].)
Possible cause
•  DSC HU/CM malfunction
―  Solenoid valve malfunction
―  Malfunction in solenoid valve internal circuit
System wiring diagram
Not applicable
Connector diagram
Not applicable


Diagnostic Procedure

Step

Inspection

Results

Action

1
VERIFY SOLENOID VALVE OPERATION
•  Verify if the solenoid valve operates using the simulation item corresponding to the displayed DTC.
―  C0001:01
•  TCS_ISOLAT_VLV_1
―  C0002:01
•  TCS_ISOLAT_VLV_2
―  C0003:01
•  TCS_SUPPLY_1
―  C0004:01
•  TCS_SUPPLY_2
―  C0010:01
•  TCS_ISOLAT_VLV_L/F
―  C0011:01
•  TCS_DUMP_L/F
―  C0014:01
•  TCS_ISOLAT_VLV_R/F
―  C0015:01
•  TCS_DUMP_R/F
―  C0018:01
•  TCS_ISOLAT_VLV_L/R
―  C0019:01
•  TCS_DUMP_L/R
―  C001C:01
•  TCS_ISOLAT_VLV_R/R
―  C001D:01
•  TCS_DUMP_R/R
•  Does the solenoid valve operate?
Yes
Go to the next step.
No
Replace the DSC HU/CM and perform the repair completion verification procedure.
Repair completion verification 1
VERIFY THAT VEHICLE IS REPAIRED
•  Install/connect the part removed/disconnected during the troubleshooting procedure.
•  Clear the DTC recorded in the memory.
•  Perform the DTC inspection for the DSC HU/CM.
•  Is the same Pending DTC present?
Yes
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
If the CAN communication is normal, perform the diagnosis from Step 1.
•  If the malfunction recurs, replace the DSC HU/CM, then go to the next step.
No
Go to the next step.
Repair completion verification 2
VERIFY IF OTHER DTCs DISPLAYED
•  Perform the DTC inspection.
•  Are any DTCs displayed?
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
No
DTC troubleshooting completed.