Home

Mazdamanuals.com

DTC B10AD:95 [BODY CONTROL MODULE (BCM)]

id0902r7102600

Outline

System malfunction location

Improper assembly of humidity sensor/solar radiation sensor/auto light sensor/rain sensor

Detection condition

•  Destination information recorded in humidity sensor/solar radiation sensor/auto light sensor/rain sensor and destination information input by performing configuration are incompatible.

Fail-safe

Not applicable

Possible cause

•  Body control module (BCM) configuration is not completed.

•  Improper assembly of humidity sensor/solar radiation sensor/auto light sensor/rain sensor

•  Humidity sensor/solar radiation sensor/auto light sensor/rain sensor malfunction

•  Body control module (BCM) malfunction

System wiring diagram

Not applicable

Connector diagram

Not applicable

System malfunction location	Improper assembly of humidity sensor/solar radiation sensor/auto light sensor/rain sensor
Detection condition	• Destination information recorded in humidity sensor/solar radiation sensor/auto light sensor/rain sensor and destination information input by performing configuration are incompatible.
Fail-safe	Not applicable
Possible cause	• Body control module (BCM) configuration is not completed. • Improper assembly of humidity sensor/solar radiation sensor/auto light sensor/rain sensor • Humidity sensor/solar radiation sensor/auto light sensor/rain sensor malfunction • Body control module (BCM) malfunction
System wiring diagram	Not applicable
Connector diagram	Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

VERIFY BODY CONTROL MODULE (BCM) DTCs AGAIN

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Perform the DTC inspection for the body control module (BCM).
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Go to the next step.

No

Go to repair completion verification 2.

2

RESET CONFIGURATION DATA FOR BODY CONTROL MODULE (BCM)

•  Using the M-MDS, perform the body control module (BCM) configuration.
(See CONFIGURATION.)

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Perform the DTC inspection for the body control module (BCM).
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Perform the body control module (BCM) configuration again, then go to the next step.

(See CONFIGURATION.)

No

Go to repair completion verification 2.

3

VERIFY PART NUMBER OF HUMIDITY SENSOR/SOLAR RADIATION SENSOR/AUTO LIGHT SENSOR/RAIN SENSOR

•  Remove the humidity sensor/solar radiation sensor/auto light sensor/rain sensor.
(See RAIN SENSOR REMOVAL/INSTALLATION.)

•  Is the part number of the humidity sensor/solar radiation sensor/auto light sensor/rain sensor correct?

Yes

Install the humidity sensor/solar radiation sensor/auto light sensor/rain sensor, then go to the next step.

(See RAIN SENSOR REMOVAL/INSTALLATION.)

No

Replace the humidity sensor/solar radiation sensor/auto light sensor/rain sensor and perform the repair completion verification.

(See RAIN SENSOR REMOVAL/INSTALLATION.)

4

INSPECT HUMIDITY SENSOR/SOLAR RADIATION SENSOR/AUTO LIGHT SENSOR/RAIN SENSOR FOR MALFUNCTION DEPENDING ON REPEATABILITY

•  Install/connect the part removed/disconnected during the troubleshooting procedure.

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Perform the DTC inspection for the body control module (BCM).
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, replace the humidity sensor/solar radiation sensor/auto light sensor/rain sensor and perform the repair completion verification.

(See RAIN SENSOR REMOVAL/INSTALLATION.)

No

Go to repair completion verification 2.

Repair completion verification 1

VERIFY THAT VEHICLE IS REPAIRED

•  Install/connect the part removed/disconnected during the troubleshooting procedure.

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Perform the DTC inspection for the body control module (BCM).
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction recurs, replace the body control module (BCM), then go to the next step.
(See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION [(E)].)

No

Go to the next step.

Repair completion verification 2

VERIFY IF OTHER DTC IS DISPLAYED

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	VERIFY BODY CONTROL MODULE (BCM) DTCs AGAIN • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Go to the next step.
1		No	Go to repair completion verification 2.
2	RESET CONFIGURATION DATA FOR BODY CONTROL MODULE (BCM) • Using the M-MDS, perform the body control module (BCM) configuration. (See CONFIGURATION.) • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Perform the body control module (BCM) configuration again, then go to the next step. (See CONFIGURATION.)
2		No	Go to repair completion verification 2.
3	VERIFY PART NUMBER OF HUMIDITY SENSOR/SOLAR RADIATION SENSOR/AUTO LIGHT SENSOR/RAIN SENSOR • Remove the humidity sensor/solar radiation sensor/auto light sensor/rain sensor. (See RAIN SENSOR REMOVAL/INSTALLATION.) • Is the part number of the humidity sensor/solar radiation sensor/auto light sensor/rain sensor correct?	Yes	Install the humidity sensor/solar radiation sensor/auto light sensor/rain sensor, then go to the next step. (See RAIN SENSOR REMOVAL/INSTALLATION.)
3		No	Replace the humidity sensor/solar radiation sensor/auto light sensor/rain sensor and perform the repair completion verification. (See RAIN SENSOR REMOVAL/INSTALLATION.)
4	INSPECT HUMIDITY SENSOR/SOLAR RADIATION SENSOR/AUTO LIGHT SENSOR/RAIN SENSOR FOR MALFUNCTION DEPENDING ON REPEATABILITY • Install/connect the part removed/disconnected during the troubleshooting procedure. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, replace the humidity sensor/solar radiation sensor/auto light sensor/rain sensor and perform the repair completion verification. (See RAIN SENSOR REMOVAL/INSTALLATION.)
4		No	Go to repair completion verification 2.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction recurs, replace the body control module (BCM), then go to the next step. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION [(E)].)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTC IS DISPLAYED • Perform the DTC inspection. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.