Home

Mazdamanuals.com

DTC B200A:62 [BODY CONTROL MODULE (BCM)]

id0902r7136300

Outline

System malfunction location

Liftgate open/close signal malfunction

Detection condition

•  The body control module (BCM) detects that the power liftgate (PLG) control module signal and the liftgate open/close are incompatible.

Fail-safe

Not applicable

Possible cause

•  The body control module (BCM) was replaced with the liftgate closed.

•  A power liftgate (PLG) control module from another vehicle is installed.

•  Power liftgate (PLG) control module malfunction

•  Body control module (BCM) malfunction

System wiring diagram

Not applicable

Connector diagram

Not applicable

System malfunction location	Liftgate open/close signal malfunction
Detection condition	• The body control module (BCM) detects that the power liftgate (PLG) control module signal and the liftgate open/close are incompatible.
Fail-safe	Not applicable
Possible cause	• The body control module (BCM) was replaced with the liftgate closed. • A power liftgate (PLG) control module from another vehicle is installed. • Power liftgate (PLG) control module malfunction • Body control module (BCM) malfunction
System wiring diagram	Not applicable
Connector diagram	Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

VERIFY IF POWER LIFTGATE (PLG) CONTROL MODULE FROM ANOTHER VEHICLE IS INSTALLED

•  Verify if a power liftgate (PLG) control module from another vehicle is installed.

•  Is a power liftgate (PLG) control module from another vehicle installed?

Yes

Replace it with the correct power liftgate (PLG) control module and perform the repair completion verification.

(See POWER LIFTGATE (PLG) CONTROL MODULE REMOVAL/INSTALLATION.)

No

Go to the next step.

2

INSPECT POWER LIFTGATE (PLG) CONTROL MODULE FOR MALFUNCTION DEPENDING ON REPEATABILITY

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Operate the power liftgate (PLG) system.

•  Perform the DTC inspection for the body control module (BCM).
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, replace the power liftgate (PLG) control module and perform the repair completion verification.

(See POWER LIFTGATE (PLG) CONTROL MODULE REMOVAL/INSTALLATION.)

No

Go to repair completion verification 2.

Repair completion verification 1

VERIFY THAT VEHICLE IS REPAIRED

•  Install/connect the part removed/disconnected during the troubleshooting procedure.

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Perform the DTC inspection for the body control module (BCM).
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction recurs, replace the body control module (BCM), then go to the next step.
(See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION [(E)].)

No

Go to the next step.

Repair completion verification 2

VERIFY IF OTHER DTC IS DISPLAYED

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	VERIFY IF POWER LIFTGATE (PLG) CONTROL MODULE FROM ANOTHER VEHICLE IS INSTALLED • Verify if a power liftgate (PLG) control module from another vehicle is installed. • Is a power liftgate (PLG) control module from another vehicle installed?	Yes	Replace it with the correct power liftgate (PLG) control module and perform the repair completion verification. (See POWER LIFTGATE (PLG) CONTROL MODULE REMOVAL/INSTALLATION.)
1		No	Go to the next step.
2	INSPECT POWER LIFTGATE (PLG) CONTROL MODULE FOR MALFUNCTION DEPENDING ON REPEATABILITY • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Operate the power liftgate (PLG) system. • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, replace the power liftgate (PLG) control module and perform the repair completion verification. (See POWER LIFTGATE (PLG) CONTROL MODULE REMOVAL/INSTALLATION.)
2		No	Go to repair completion verification 2.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction recurs, replace the body control module (BCM), then go to the next step. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION [(E)].)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTC IS DISPLAYED • Perform the DTC inspection. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.