Home

Mazdamanuals.com

 DTC P0562 [MZR-CD (RF Turbo)]

DTC P0562 [MZR-CD (RF Turbo)]

id0102f1832600

DTC P0562

Battery voltage low input

DETECTION CONDITION

• The PCM monitors the battery voltage. If the battery voltage is less than 8 V, the PCM determines that there is a malfunction in the battery and the battery signal system.
Diagnostic support note
• The MIL illuminates if the PCM detects the above malfunction condition in the first drive cycle.
• FREEZE FRAME DATA is available.
• The DTC is stored in the PCM memory.

POSSIBLE CAUSE

• Drive belt condition
• Generator malfunction
• Open circuit in wiring harness between generator terminal D and PCM terminal 9
• Open circuit in wiring harness between generator terminal P and PCM terminal 77
• Short to ground in wiring harness between generator terminal D and PCM terminal 9
• Short to ground in wiring harness between generator terminal P and PCM terminal 77
• Poor connection of connector at positive terminal
• Poor battery positive terminal
• Terminal malfunction
• PCM malfunction

Diagnostic procedure

STEP

INSPECTION

ACTION

1
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has FREEZE FRAME DATA been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
• Verify related service repair information availability.
• Is any related repair information available?
Yes
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY CURRENT SIGNAL STATUS: IS CONCERN INTERMITTENT OR CONSTANT?
• Connect the WDS or equivalent to the DLC-2.
• Clear the DTC from the PCM memory using the WDS or equivalent.
• Start the engine.
• Is the same DTC present?
Yes
Go to the next step.
No
Intermittent concern exists.
Perform the "INTERMITTENT CONCERN TROUBLESHOOTING".
4
INSPECT DRIVE BELT CONDITION
• Verify that drive belt auto tensioner indicator mark does not exceed limit.
• Is drive belt normal?
Yes
Go to the next step.
No
Replace and/or adjust drive belt, then go to Step 9.
5
INSPECT GENERATOR TERMINAL FOR POOR INSTALLATION
• Turn the engine switch off.
• Inspect generator terminal B for looseness.
• Is there any malfunction?
Yes
Connect generator terminal B correctly, then go to Step 9.
No
Go to the next step.
6
INSPECT GENERATOR
• Inspect the generator.
• Is there any malfunction?
Yes
Replace the generator, then go to Step 9.
No
Go to the next step.
7
INSPECT GENERATOR CIRCUIT FOR OPEN CIRCUIT
• Inspect for continuity between the following terminal:
- Generator terminal D (wiring harness-side) and PCM terminal 9
- Generator terminal P (wiring harness-side) and PCM terminal 77
• Are there continuity?
Yes
Go to the next step.
No
Repair or replace the wiring harness for open, then go to Step 9.
8
INSPECT GENERATOR CIRCUIT FOR SHORT TO GROUND
• Inspect for continuity between the following terminal:
- Generator terminal D (wiring harness-side) and PCM terminal 9
- Generator terminal P (wiring harness-side) and PCM terminal 77
• Are there continuity?
Yes
Go to the next step.
No
Repair or replace the wiring harness for short, then go to the next step.
9
VERIFY TROUBLESHOOTING OF DTC P0562 COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the WDS or equivalent.
• Start the engine.
• Is the same DTC present?
Yes
Replace the PCM, then go to the next step.
No
Go to the next step.
10
VERIFY AFTER REPAIR PROCEDURE
• Perform the Repair Verification Drive Mode.
• Are any DTCs present?
Yes
Go to the applicable DTC inspection.
No
DTC troubleshooting completed.