Home

Mazdamanuals.com

DTC U2300:55 [DSC HU/CM]

id040262013000

Outline

System malfunction location

Configuration data

Detection condition

•  The DSC HU/CM detects any of the following conditions.

―  Configuration procedure not completed

―  Signal in which configuration was not implemented is received from body control module (BCM) and PCM

Fail-safe

Refer to “DTC Table” and “Fail-safe Function Malfunction Contents Table”.(See DTC TABLE [DSC HU/CM (E)].)

Possible cause

Note

•  To correctly write the configuration data sent from the body control module (BCM) and PCM to DSC HU/CM, 30 s or more have to be elapsed since the ignition is switched ON (engine off or on).

•  DTCs are stored in the body control module (BCM).

―  Body control module (BCM) configuration not implemented

―  Body control module (BCM) internal memory malfunction

•  Configuration procedure was not completed properly.

•  PCM malfunction

•  Body control module (BCM) malfunction

•  DSC HU/CM malfunction

System wiring diagram

Not applicable

Connector diagram

Not applicable

System malfunction location	Configuration data
Detection condition	• The DSC HU/CM detects any of the following conditions. ― Configuration procedure not completed ― Signal in which configuration was not implemented is received from body control module (BCM) and PCM
Fail-safe	Refer to “DTC Table” and “Fail-safe Function Malfunction Contents Table”.(See DTC TABLE [DSC HU/CM (E)].)
Possible cause	Note • To correctly write the configuration data sent from the body control module (BCM) and PCM to DSC HU/CM, 30 s or more have to be elapsed since the ignition is switched ON (engine off or on). • DTCs are stored in the body control module (BCM). ― Body control module (BCM) configuration not implemented ― Body control module (BCM) internal memory malfunction • Configuration procedure was not completed properly. • PCM malfunction • Body control module (BCM) malfunction • DSC HU/CM malfunction
System wiring diagram	Not applicable
Connector diagram	Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

INSPECT PCM FOR MALFUNCTION

•  Perform the DTC inspection for PCM.
(See DTC INSPECTION.)

•  Are any DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [PCM (SKYACTIV-G (E))].)

(See DTC TABLE [PCM (SKYACTIV-D)].)

No

Go to the next step.

2

INSPECT BODY CONTROL MODULE (BCM) FOR MALFUNCTION

•  Perform the DTC inspection for body control module (BCM).
(See DTC INSPECTION.)

•  Are any DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [BODY CONTROL MODULE (BCM) (E)].)

No

Go to the next step.

3

VERIFY REPLACEMENT RECORD OF DSC HU/CM

•  Before performing the troubleshooting diagnostic procedure this time, verify if the DSC HU/CM was replaced.

•  Was the DSC HU/CM replaced?

Yes

After reimplementing the required servicing when replacing the DSC HU/CM in accordance with DSC HU/CM removal/installation, perform the repair completion verification.

(See DSC HU/CM REMOVAL/INSTALLATION [L.H.D. (E)].)

(See DSC HU/CM REMOVAL/INSTALLATION [R.H.D.].)

No

Go to the next step.

4

RESET CONFIGURATION DATA FOR BODY CONTROL MODULE (BCM)

•  Perform the body control module (BCM) configuration using the M-MDS.
(See CONFIGURATION.)

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Switch the ignition ON (engine off or on) and wait for 30 s or more.

•  Perform the DTC inspection for the DSC HU/CM.
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Perform the body control module (BCM) configuration again using the M-MDS and perform the repair completion verification.

No

Go to repair completion verification 2.

Repair completion verification 1

VERIFY THAT VEHICLE IS REPAIRED

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Switch the ignition ON (engine off or on) and wait for 30 s or more.

•  Perform the DTC inspection for the DSC HU/CM.
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction recurs, replace the DSC HU/CM, then go to the next step.
(See DSC HU/CM REMOVAL/INSTALLATION [L.H.D. (E)].)

(See DSC HU/CM REMOVAL/INSTALLATION [R.H.D.].)

No

Go to the next step.

Repair completion verification 2

VERIFY IF OTHER DTC IS DISPLAYED

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	INSPECT PCM FOR MALFUNCTION • Perform the DTC inspection for PCM. (See DTC INSPECTION.) • Are any DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [PCM (SKYACTIV-G (E))].) (See DTC TABLE [PCM (SKYACTIV-D)].)
1		No	Go to the next step.
2	INSPECT BODY CONTROL MODULE (BCM) FOR MALFUNCTION • Perform the DTC inspection for body control module (BCM). (See DTC INSPECTION.) • Are any DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [BODY CONTROL MODULE (BCM) (E)].)
2		No	Go to the next step.
3	VERIFY REPLACEMENT RECORD OF DSC HU/CM • Before performing the troubleshooting diagnostic procedure this time, verify if the DSC HU/CM was replaced. • Was the DSC HU/CM replaced?	Yes	After reimplementing the required servicing when replacing the DSC HU/CM in accordance with DSC HU/CM removal/installation, perform the repair completion verification. (See DSC HU/CM REMOVAL/INSTALLATION [L.H.D. (E)].) (See DSC HU/CM REMOVAL/INSTALLATION [R.H.D.].)
3		No	Go to the next step.
4	RESET CONFIGURATION DATA FOR BODY CONTROL MODULE (BCM) • Perform the body control module (BCM) configuration using the M-MDS. (See CONFIGURATION.) • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Switch the ignition ON (engine off or on) and wait for 30 s or more. • Perform the DTC inspection for the DSC HU/CM. (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Perform the body control module (BCM) configuration again using the M-MDS and perform the repair completion verification.
4		No	Go to repair completion verification 2.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Switch the ignition ON (engine off or on) and wait for 30 s or more. • Perform the DTC inspection for the DSC HU/CM. (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction recurs, replace the DSC HU/CM, then go to the next step. (See DSC HU/CM REMOVAL/INSTALLATION [L.H.D. (E)].) (See DSC HU/CM REMOVAL/INSTALLATION [R.H.D.].)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTC IS DISPLAYED • Perform the DTC inspection. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.