Home

Mazdamanuals.com

DTC P0616:29 [BODY CONTROL MODULE (BCM)]

id0902r7092600

Outline

System malfunction location

Downstream side of starter relay signal malfunction

Detection condition

•  The body control module (BCM) detects that the following signals are unmatched for a continuous 5 times.

―  Transaxle range sensor (ATX) or starter interlock switch (MTX) condition

―  Starter relay downstream circuit condition

―  PCM control result

―  CAN signal condition output from PCM

Fail-safe

Not applicable

Possible cause

•  DTCs are stored in the PCM.

•  PCM malfunction

•  Body control module (BCM) malfunction

System wiring diagram

Not applicable

Connector diagram

Not applicable

System malfunction location	Downstream side of starter relay signal malfunction
Detection condition	• The body control module (BCM) detects that the following signals are unmatched for a continuous 5 times. ― Transaxle range sensor (ATX) or starter interlock switch (MTX) condition ― Starter relay downstream circuit condition ― PCM control result ― CAN signal condition output from PCM
Fail-safe	Not applicable
Possible cause	• DTCs are stored in the PCM. • PCM malfunction • Body control module (BCM) malfunction
System wiring diagram	Not applicable
Connector diagram	Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

VERIFY BODY CONTROL MODULE (BCM) DTCs AGAIN

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  With the programmed remote transmitter in the vehicle, switch the ignition ON (engine off).

•  Perform the following work 5 times or more.

―  Depress the clutch pedal and release it. (MTX)

―  Operate the selector lever to other than P and N position from P or N position and hold for 0.5 s or more. (ATX)

•  Perform the DTC inspection for the body control module (BCM).
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Go to the next step.

No

Go to repair completion verification 2.

2

INSPECT PCM FOR MALFUNCTION

•  Perform the DTC inspection for the PCM.
(See DTC INSPECTION.)

•  Is a DTC displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [PCM (SKYACTIV-G (E))].)

(See DTC TABLE [PCM (SKYACTIV-D)].)

(See DTC TABLE [PCM (SKYACTIV-X)].)

No

Go to the next step.

3

INSPECT PCM FOR MALFUNCTION DEPENDING ON REPEATABILITY

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  With the programmed remote transmitter in the vehicle, switch the ignition ON (engine off).

•  Perform the following work 5 times or more.

―  Depress the clutch pedal and release it. (MTX)

―  Operate the selector lever to other than P and N position from P or N position and hold for 0.5 s or more. (ATX)

•  Perform the DTC inspection for the body control module (BCM).
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, replace the PCM and perform the repair completion verification.

(See PCM REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)

(See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (E))].)

(See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (E))].)

(See PCM REMOVAL/INSTALLATION [SKYACTIV-X 2.0].)

No

Go to repair completion verification 2.

Repair completion verification 1

VERIFY THAT VEHICLE IS REPAIRED

•  Install/connect the part removed/disconnected during the troubleshooting procedure.

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  With the programmed remote transmitter in the vehicle, switch the ignition ON (engine off).

•  Perform the following work 5 times or more.

―  Depress the clutch pedal and release it. (MTX)

―  Operate the selector lever to other than P and N position from P or N position and hold for 0.5 s or more. (ATX)

•  Perform the DTC inspection for the body control module (BCM).
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction recurs, replace the body control module (BCM), then go to the next step.
(See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION [(E)].)

No

Go to the next step.

Repair completion verification 2

VERIFY IF OTHER DTC IS DISPLAYED

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	VERIFY BODY CONTROL MODULE (BCM) DTCs AGAIN • Clear the DTC recorded in the memory. (See CLEARING DTC.) • With the programmed remote transmitter in the vehicle, switch the ignition ON (engine off). • Perform the following work 5 times or more. ― Depress the clutch pedal and release it. (MTX) ― Operate the selector lever to other than P and N position from P or N position and hold for 0.5 s or more. (ATX) • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Go to the next step.
1		No	Go to repair completion verification 2.
2	INSPECT PCM FOR MALFUNCTION • Perform the DTC inspection for the PCM. (See DTC INSPECTION.) • Is a DTC displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [PCM (SKYACTIV-G (E))].) (See DTC TABLE [PCM (SKYACTIV-D)].) (See DTC TABLE [PCM (SKYACTIV-X)].)
2		No	Go to the next step.
3	INSPECT PCM FOR MALFUNCTION DEPENDING ON REPEATABILITY • Clear the DTC recorded in the memory. (See CLEARING DTC.) • With the programmed remote transmitter in the vehicle, switch the ignition ON (engine off). • Perform the following work 5 times or more. ― Depress the clutch pedal and release it. (MTX) ― Operate the selector lever to other than P and N position from P or N position and hold for 0.5 s or more. (ATX) • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, replace the PCM and perform the repair completion verification. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 1.8].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (E))].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (E))].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-X 2.0].)
3		No	Go to repair completion verification 2.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • With the programmed remote transmitter in the vehicle, switch the ignition ON (engine off). • Perform the following work 5 times or more. ― Depress the clutch pedal and release it. (MTX) ― Operate the selector lever to other than P and N position from P or N position and hold for 0.5 s or more. (ATX) • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction recurs, replace the body control module (BCM), then go to the next step. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION [(E)].)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTC IS DISPLAYED • Perform the DTC inspection. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.