DTC B14F7:64 [VEHICLE CONTROL MODULE]

System malfunction location	Configuration data of body control module (BCM) not matched
Detection condition	• The vehicle control module (VCM) detects that the configuration data of the 360°view monitor control module and the body control module (BCM) is not matched for 10 s.
Fail-safe	(See DTC TABLE [VEHICLE CONTROL MODULE (E)].)
Possible cause	• Malfunction in CAN communication line between body control module (BCM) and 360°view monitor control module • Inappropriate 360°view monitor control module replacement procedure • Configuration data of body control module (BCM) and 360°view monitor control module is not matched ― Body control module (BCM) configuration data write error ― Configuration not completed after 360°view monitor control module replacement • 360°view monitor control module malfunction • Body control module (BCM) malfunction
System wiring diagram	Not applicable
Connector diagram	Not applicable

System malfunction location

Configuration data of body control module (BCM) not matched

Detection condition

• The vehicle control module (VCM) detects that the configuration data of the 360°view monitor control module and the body control module (BCM) is not matched for 10 s.

Fail-safe

(See DTC TABLE [VEHICLE CONTROL MODULE (E)].)

Possible cause

• Malfunction in CAN communication line between body control module (BCM) and 360°view monitor control module

• Inappropriate 360°view monitor control module replacement procedure

• Configuration data of body control module (BCM) and 360°view monitor control module is not matched

― Body control module (BCM) configuration data write error

― Configuration not completed after 360°view monitor control module replacement

• 360°view monitor control module malfunction

• Body control module (BCM) malfunction

System wiring diagram

Not applicable

Connector diagram

Not applicable

Step	Inspection	Results	Action
1	INSPECT VEHICLE CONTROL MODULE (VCM) AND BODY CONTROL MODULE (BCM) FOR MALFUNCTION • Perform the DTC inspection for the vehicle control module (VCM) and the body control module (BCM). (See DTC INSPECTION.) • Is a DTC related to an internal malfunction displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [VEHICLE CONTROL MODULE (E)].) (See DTC TABLE [BODY CONTROL MODULE (BCM) (E)].)
No	Go to the next step.
2	INSPECT 360°VIEW MONITOR CONTROL MODULE FOR MALFUNCTION • Perform the DTC inspection for the 360°view monitor control module. (See DTC INSPECTION.) • Is a DTC displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [360°VIEW MONITOR CONTROL MODULE (E)].)
No	Go to the next step.
3	VERIFY REPLACEMENT RECORD OF 360°VIEW MONITOR CONTROL MODULE • Before performing the troubleshooting diagnostic procedure this time, verify if the 360°view monitor control module was replaced. • Was the 360°view monitor control module replaced?	Yes	After re-implementing the required servicing when replacing the 360°view monitor control module in accordance with 360°view monitor control module removal/installation, perform the repair completion verification. (See 360°VIEW MONITOR CONTROL MODULE REMOVAL/INSTALLATION [(E)].)
No	Go to the next step.
4	VERIFY IF MALFUNCTION IS CAUSED BY BODY CONTROL MODULE (BCM) CONFIGURATION ERROR • Switch the ignition OFF and wait for 30 s or more. • Switch the ignition ON (engine off or on) and wait for 30 s or more. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Go to the next step.
No	Go to repair completion verification 2.
5	VERIFY BODY CONTROL MODULE (BCM) CONFIGURATION-RELATED DTCs • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is a configuration related DTC displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [BODY CONTROL MODULE (BCM) (E)].)
No	Go to the next step.
6	RESET CONFIGURATION DATA FOR BODY CONTROL MODULE (BCM) • Using the M-MDS, perform the body control module (BCM) configuration. (See CONFIGURATION.) • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Switch the ignition OFF and wait for 30 s or more. • Switch the ignition ON (engine off or on) and wait for 30 s or more. • Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Replace the 360°view monitor control module and perform the repair completion verification. (See 360°VIEW MONITOR CONTROL MODULE REMOVAL/INSTALLATION [(E)].)
No	Go to repair completion verification 2.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction recurs, replace the body control module (BCM), then go to the next step. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION [(E)].)
No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTC IS DISPLAYED • Perform the DTC inspection. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
No	DTC troubleshooting completed.

Step

Inspection

Results

Action

INSPECT VEHICLE CONTROL MODULE (VCM) AND BODY CONTROL MODULE (BCM) FOR MALFUNCTION

• Perform the DTC inspection for the vehicle control module (VCM) and the body control module (BCM).

(See DTC INSPECTION.)

• Is a DTC related to an internal malfunction displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [VEHICLE CONTROL MODULE (E)].)

(See DTC TABLE [BODY CONTROL MODULE (BCM) (E)].)

Go to the next step.

INSPECT 360°VIEW MONITOR CONTROL MODULE FOR MALFUNCTION

• Perform the DTC inspection for the 360°view monitor control module.

(See DTC INSPECTION.)

• Is a DTC displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [360°VIEW MONITOR CONTROL MODULE (E)].)

Go to the next step.

VERIFY REPLACEMENT RECORD OF 360°VIEW MONITOR CONTROL MODULE

• Before performing the troubleshooting diagnostic procedure this time, verify if the 360°view monitor control module was replaced.

• Was the 360°view monitor control module replaced?

Yes

After re-implementing the required servicing when replacing the 360°view monitor control module in accordance with 360°view monitor control module removal/installation, perform the repair completion verification.

(See 360°VIEW MONITOR CONTROL MODULE REMOVAL/INSTALLATION [(E)].)

Go to the next step.

VERIFY IF MALFUNCTION IS CAUSED BY BODY CONTROL MODULE (BCM) CONFIGURATION ERROR

• Switch the ignition OFF and wait for 30 s or more.

• Switch the ignition ON (engine off or on) and wait for 30 s or more.

• Clear the DTC recorded in the memory.

(See CLEARING DTC.)

• Perform the DTC inspection for the vehicle control module (VCM).

(See DTC INSPECTION.)

• Is the same Pending DTC present?

Yes

Go to the next step.

Go to repair completion verification 2.

VERIFY BODY CONTROL MODULE (BCM) CONFIGURATION-RELATED DTCs

• Clear the DTC recorded in the memory.

(See CLEARING DTC.)

• Perform the DTC inspection for the body control module (BCM).

(See DTC INSPECTION.)

• Is a configuration related DTC displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [BODY CONTROL MODULE (BCM) (E)].)

Go to the next step.

RESET CONFIGURATION DATA FOR BODY CONTROL MODULE (BCM)

• Using the M-MDS, perform the body control module (BCM) configuration.

(See CONFIGURATION.)

• Clear the DTC recorded in the memory.

(See CLEARING DTC.)

• Switch the ignition OFF and wait for 30 s or more.

• Switch the ignition ON (engine off or on) and wait for 30 s or more.

• Perform the DTC inspection for the vehicle control module (VCM).

(See DTC INSPECTION.)

• Is the same Pending DTC present?

Yes

Replace the 360°view monitor control module and perform the repair completion verification.

(See 360°VIEW MONITOR CONTROL MODULE REMOVAL/INSTALLATION [(E)].)

Go to repair completion verification 2.

Repair completion verification 1

VERIFY THAT VEHICLE IS REPAIRED

• Install/connect the part removed/disconnected during the troubleshooting procedure.

• Clear the DTC recorded in the memory.

(See CLEARING DTC.)

• Perform the DTC inspection for the vehicle control module (VCM).

(See DTC INSPECTION.)

• Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

• If the malfunction recurs, replace the body control module (BCM), then go to the next step.

(See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION [(E)].)

Go to the next step.

Repair completion verification 2

VERIFY IF OTHER DTC IS DISPLAYED

• Perform the DTC inspection.

(See DTC INSPECTION.)

• Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

DTC troubleshooting completed.

System malfunction location	Configuration data of body control module (BCM) not matched
Detection condition	• The vehicle control module (VCM) detects that the configuration data of the parking assist unit (optical) and the body control module (BCM) is not matched for 10 s.
Fail-safe	(See DTC TABLE [VEHICLE CONTROL MODULE (E)].)
Possible cause	• Malfunction in CAN communication line between body control module (BCM) and parking assist unit (optical) • Inappropriate parking assist unit (optical) replacement procedure • Configuration data of body control module (BCM) and parking assist unit (optical) is not matched ― Body control module (BCM) configuration data write error ― Configuration not completed after parking assist unit (optical) replacement • Parking assist unit (optical) malfunction • Body control module (BCM) malfunction
System wiring diagram	Not applicable
Connector diagram	Not applicable

System malfunction location

Configuration data of body control module (BCM) not matched

Detection condition

• The vehicle control module (VCM) detects that the configuration data of the parking assist unit (optical) and the body control module (BCM) is not matched for 10 s.

Fail-safe

(See DTC TABLE [VEHICLE CONTROL MODULE (E)].)

Possible cause

• Malfunction in CAN communication line between body control module (BCM) and parking assist unit (optical)

• Inappropriate parking assist unit (optical) replacement procedure

• Configuration data of body control module (BCM) and parking assist unit (optical) is not matched

― Body control module (BCM) configuration data write error

― Configuration not completed after parking assist unit (optical) replacement

• Parking assist unit (optical) malfunction

• Body control module (BCM) malfunction

System wiring diagram

Not applicable

Connector diagram

Not applicable

Step	Inspection	Results	Action
1	INSPECT VEHICLE CONTROL MODULE (VCM) AND BODY CONTROL MODULE (BCM) FOR MALFUNCTION • Perform the DTC inspection for the vehicle control module (VCM) and the body control module (BCM). (See DTC INSPECTION.) • Is a DTC related to an internal malfunction displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [VEHICLE CONTROL MODULE (E)].) (See DTC TABLE [BODY CONTROL MODULE (BCM) (E)].)
No	Go to the next step.
2	INSPECT PARKING ASSIST UNIT (OPTICAL) FOR MALFUNCTION • Perform the DTC inspection for the parking assist unit (optical). (See DTC INSPECTION.) • Is a DTC displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [PARKING ASSIST UNIT (OPTICAL) (E)].)
No	Go to the next step.
3	VERIFY REPLACEMENT RECORD OF PARKING ASSIST UNIT (OPTICAL) • Before performing the troubleshooting diagnostic procedure this time, verify if the parking assist unit (optical) was replaced. • Was the parking assist unit (optical) replaced?	Yes	After re-implementing the required servicing when replacing the parking assist unit (optical) in accordance with parking assist unit (optical) removal/installation, perform the repair completion verification. (See PARKING ASSIST UNIT (OPTICAL) REMOVAL/INSTALLATION [(E)].)
No	Go to the next step.
4	VERIFY IF MALFUNCTION IS CAUSED BY BODY CONTROL MODULE (BCM) CONFIGURATION ERROR • Switch the ignition OFF and wait for 30 s or more. • Switch the ignition ON (engine off or on) and wait for 30 s or more. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Go to the next step.
No	Go to repair completion verification 2.
5	VERIFY BODY CONTROL MODULE (BCM) CONFIGURATION-RELATED DTCs • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.) • Is a configuration related DTC displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [BODY CONTROL MODULE (BCM) (E)].)
No	Go to the next step.
6	RESET CONFIGURATION DATA FOR BODY CONTROL MODULE (BCM) • Using the M-MDS, perform the body control module (BCM) configuration. (See CONFIGURATION.) • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Switch the ignition OFF and wait for 30 s or more. • Switch the ignition ON (engine off or on) and wait for 30 s or more. • Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Replace the parking assist unit (optical) and perform the repair completion verification. (See PARKING ASSIST UNIT (OPTICAL) REMOVAL/INSTALLATION [(E)].)
No	Go to repair completion verification 2.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction recurs, replace the body control module (BCM), then go to the next step. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION [(E)].)
No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTC IS DISPLAYED • Perform the DTC inspection. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
No	DTC troubleshooting completed.

Step

Inspection

Results

Action

INSPECT VEHICLE CONTROL MODULE (VCM) AND BODY CONTROL MODULE (BCM) FOR MALFUNCTION

• Perform the DTC inspection for the vehicle control module (VCM) and the body control module (BCM).

(See DTC INSPECTION.)

• Is a DTC related to an internal malfunction displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [VEHICLE CONTROL MODULE (E)].)

(See DTC TABLE [BODY CONTROL MODULE (BCM) (E)].)

Go to the next step.

INSPECT PARKING ASSIST UNIT (OPTICAL) FOR MALFUNCTION

• Perform the DTC inspection for the parking assist unit (optical).

(See DTC INSPECTION.)

• Is a DTC displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [PARKING ASSIST UNIT (OPTICAL) (E)].)

Go to the next step.

VERIFY REPLACEMENT RECORD OF PARKING ASSIST UNIT (OPTICAL)

• Before performing the troubleshooting diagnostic procedure this time, verify if the parking assist unit (optical) was replaced.

• Was the parking assist unit (optical) replaced?

Yes

After re-implementing the required servicing when replacing the parking assist unit (optical) in accordance with parking assist unit (optical) removal/installation, perform the repair completion verification.

(See PARKING ASSIST UNIT (OPTICAL) REMOVAL/INSTALLATION [(E)].)

Go to the next step.

VERIFY IF MALFUNCTION IS CAUSED BY BODY CONTROL MODULE (BCM) CONFIGURATION ERROR

• Switch the ignition OFF and wait for 30 s or more.

• Switch the ignition ON (engine off or on) and wait for 30 s or more.

• Clear the DTC recorded in the memory.

(See CLEARING DTC.)

• Perform the DTC inspection for the vehicle control module (VCM).

(See DTC INSPECTION.)

• Is the same Pending DTC present?

Yes

Go to the next step.

Go to repair completion verification 2.

VERIFY BODY CONTROL MODULE (BCM) CONFIGURATION-RELATED DTCs

• Clear the DTC recorded in the memory.

(See CLEARING DTC.)

• Perform the DTC inspection for the body control module (BCM).

(See DTC INSPECTION.)

• Is a configuration related DTC displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [BODY CONTROL MODULE (BCM) (E)].)

Go to the next step.

RESET CONFIGURATION DATA FOR BODY CONTROL MODULE (BCM)

• Using the M-MDS, perform the body control module (BCM) configuration.

(See CONFIGURATION.)

• Clear the DTC recorded in the memory.

(See CLEARING DTC.)

• Switch the ignition OFF and wait for 30 s or more.

• Switch the ignition ON (engine off or on) and wait for 30 s or more.

• Perform the DTC inspection for the vehicle control module (VCM).

(See DTC INSPECTION.)

• Is the same Pending DTC present?

Yes

Replace the parking assist unit (optical) and perform the repair completion verification.

(See PARKING ASSIST UNIT (OPTICAL) REMOVAL/INSTALLATION [(E)].)

Go to repair completion verification 2.

Repair completion verification 1

VERIFY THAT VEHICLE IS REPAIRED

• Install/connect the part removed/disconnected during the troubleshooting procedure.

• Clear the DTC recorded in the memory.

(See CLEARING DTC.)

• Perform the DTC inspection for the vehicle control module (VCM).

(See DTC INSPECTION.)

• Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

• If the malfunction recurs, replace the body control module (BCM), then go to the next step.

(See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION [(E)].)

Go to the next step.

Repair completion verification 2

VERIFY IF OTHER DTC IS DISPLAYED

• Perform the DTC inspection.

(See DTC INSPECTION.)

• Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

DTC troubleshooting completed.

Mazdamanuals.com