Home

Mazdamanuals.com

DTC P1336:00 [PCM (SKYACTIV-D)]

id0102t5317400

Outline

System malfunction location

CKP sensor/CMP sensor malfunction

Detection condition

•  The phase difference between the CKP sensor and the CMP sensor exceeds the specification. (Determines stretched timing chain)

Fail-safe

•  Not applicable

Possible cause

•  Stretched timing chain

•  CKP sensor connector or terminal malfunction

•  CKP sensor malfunction

•  CKP sensor pulse wheel malfunction

•  CMP sensor connector or terminal malfunction

•  CMP sensor malfunction

•  CMP sensor pulse wheel malfunction

System wiring diagram

•  Not applicable

Connector diagram

•  Not applicable

System malfunction location	CKP sensor/CMP sensor malfunction
Detection condition	• The phase difference between the CKP sensor and the CMP sensor exceeds the specification. (Determines stretched timing chain)
Fail-safe	• Not applicable
Possible cause	• Stretched timing chain • CKP sensor connector or terminal malfunction • CKP sensor malfunction • CKP sensor pulse wheel malfunction • CMP sensor connector or terminal malfunction • CMP sensor malfunction • CMP sensor pulse wheel malfunction
System wiring diagram	• Not applicable
Connector diagram	• Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION

•  Record the freeze frame data/snapshot data.

Note

•  Recording can be facilitated using the screen capture function of the PC.

—

Go to the next step.

2

VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY

•  Verify related Service Bulletins, on-line repair information, or Service Information availability.

•  Is any related Information available?

Yes

Perform repair or diagnosis according to the available information.

•  If the vehicle is not repaired, go to the next step.

No

Go to the next step.

3

INSPECT FOR OTHER RELATED DTCs

•  Perform the DTC inspection for the PCM.
(See DTC INSPECTION.)

•  Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [PCM (SKYACTIV-D)].)

No

Go to the next step.

4

INSPECT CKP SENSOR CONNECTOR FOR MALFUNCTION

•  Inspect the applicable connector and terminal.
(See CONNECTOR INSPECTION.)

•  Are the connector and terminal normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

5

INSPECT CKP SENSOR FOR FOREIGN MATTER PENETRATION

•  Inspect the CKP sensor.
(See CRANKSHAFT POSITION (CKP) SENSOR INSPECTION [SKYACTIV-D 1.8].)

•  Inspect the CKP sensor for foreign matter penetration.

•  Is there foreign matter in the CKP sensor?

Yes

Remove the foreign matter from the CKP sensor, then go to repair completion verification.

No

Go to the next step.

6

INSPECT CKP SENSOR PULSE WHEEL

•  Visually inspect the CKP sensor.

•  Is there damage or loss to CKP sensor pulse wheel?

Yes

Replace the CKP sensor pulse wheel, then go to repair completion verification.

No

Go to the next step.

7

INSPECT CKP SENSOR FOR MALFUNCTION

•  Inspect the applicable part.
(See CRANKSHAFT POSITION (CKP) SENSOR INSPECTION [SKYACTIV-D 1.8].)

•  Is the part normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

(See CRANKSHAFT POSITION (CKP) SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)

8

INSPECT CMP SENSOR CONNECTOR FOR MALFUNCTION

•  Inspect the applicable connector and terminal.
(See CONNECTOR INSPECTION.)

•  Are the connector and terminal normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

9

INSPECT CMP SENSOR FOR FOREIGN MATTER PENETRATION.

•  Remove the CMP sensor.
(See CAMSHAFT POSITION (CMP) SENSOR INSPECTION [SKYACTIV-D 1.8].)

•  Inspect the CMP sensor for foreign matter penetration.

•  Is there foreign matter in the CMP sensor?

Yes

Remove the foreign matter from the CMP sensor, then go to repair completion verification.

No

Go to the next step.

10

INSPECT CMP SENSOR PULSE WHEEL

•  Inspect the CMP sensor pulse wheel.

•  Is there damage or loss to the CMP sensor pulse wheel?

Yes

Replace the CMP sensor pulse wheel, then go to repair completion verification.

No

Go to the next step.

11

INSPECT CMP SENSOR FOR MALFUNCTION

•  Inspect the applicable part.
(See CAMSHAFT POSITION (CMP) SENSOR INSPECTION [SKYACTIV-D 1.8].)

•  Is the part normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

(See CAMSHAFT POSITION (CMP) SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)

12

INSPECT PCM CONNECTOR FOR MALFUNCTION

•  Inspect the applicable connector and terminal.
(See CONNECTOR INSPECTION.)

•  Are the connector and terminal normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

13

INSPECT VALVE TIMING

•  Inspect the valve timing.
(See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)

•  Is the valve timing normal?

Yes

Go to the next step.

No

Adjust the valve timing, then go to repair completion verification.

(See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)

14

INSPECT TIMING CHAIN

•  Inspect the timing chain.
(See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)

—

Go to the next step.

15

PERFORM TIMING CHAIN LEARNING

•  Implement the timing chain learning.
(See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)

—

Go to the next step.

Repair completion verification 1

VERIFY THAT VEHICLE IS REPAIRED

•  Install/connect the part removed/disconnected during the troubleshooting procedure.

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Replicate the vehicle conditions at the time the DTC was detected using the following procedure.

―  Start the engine.

•  Perform the DTC inspection for the PCM.
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction recurs, replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)

No

Go to the next step.

Repair completion verification 2

VERIFY IF OTHER DTCs DISPLAYED

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION • Record the freeze frame data/snapshot data. Note • Recording can be facilitated using the screen capture function of the PC.	—	Go to the next step.
2	VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY • Verify related Service Bulletins, on-line repair information, or Service Information availability. • Is any related Information available?	Yes	Perform repair or diagnosis according to the available information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT FOR OTHER RELATED DTCs • Perform the DTC inspection for the PCM. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [PCM (SKYACTIV-D)].)
3		No	Go to the next step.
4	INSPECT CKP SENSOR CONNECTOR FOR MALFUNCTION • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION.) • Are the connector and terminal normal?	Yes	Go to the next step.
4		No	Repair or replace the malfunctioning location and perform the repair completion verification.
5	INSPECT CKP SENSOR FOR FOREIGN MATTER PENETRATION • Inspect the CKP sensor. (See CRANKSHAFT POSITION (CKP) SENSOR INSPECTION [SKYACTIV-D 1.8].) • Inspect the CKP sensor for foreign matter penetration. • Is there foreign matter in the CKP sensor?	Yes	Remove the foreign matter from the CKP sensor, then go to repair completion verification.
5		No	Go to the next step.
6	INSPECT CKP SENSOR PULSE WHEEL • Visually inspect the CKP sensor. • Is there damage or loss to CKP sensor pulse wheel?	Yes	Replace the CKP sensor pulse wheel, then go to repair completion verification.
6		No	Go to the next step.
7	INSPECT CKP SENSOR FOR MALFUNCTION • Inspect the applicable part. (See CRANKSHAFT POSITION (CKP) SENSOR INSPECTION [SKYACTIV-D 1.8].) • Is the part normal?	Yes	Go to the next step.
7		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See CRANKSHAFT POSITION (CKP) SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)
8	INSPECT CMP SENSOR CONNECTOR FOR MALFUNCTION • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION.) • Are the connector and terminal normal?	Yes	Go to the next step.
8		No	Repair or replace the malfunctioning location and perform the repair completion verification.
9	INSPECT CMP SENSOR FOR FOREIGN MATTER PENETRATION. • Remove the CMP sensor. (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION [SKYACTIV-D 1.8].) • Inspect the CMP sensor for foreign matter penetration. • Is there foreign matter in the CMP sensor?	Yes	Remove the foreign matter from the CMP sensor, then go to repair completion verification.
9		No	Go to the next step.
10	INSPECT CMP SENSOR PULSE WHEEL • Inspect the CMP sensor pulse wheel. • Is there damage or loss to the CMP sensor pulse wheel?	Yes	Replace the CMP sensor pulse wheel, then go to repair completion verification.
10		No	Go to the next step.
11	INSPECT CMP SENSOR FOR MALFUNCTION • Inspect the applicable part. (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION [SKYACTIV-D 1.8].) • Is the part normal?	Yes	Go to the next step.
11		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See CAMSHAFT POSITION (CMP) SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)
12	INSPECT PCM CONNECTOR FOR MALFUNCTION • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION.) • Are the connector and terminal normal?	Yes	Go to the next step.
12		No	Repair or replace the malfunctioning location and perform the repair completion verification.
13	INSPECT VALVE TIMING • Inspect the valve timing. (See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 1.8].) • Is the valve timing normal?	Yes	Go to the next step.
13		No	Adjust the valve timing, then go to repair completion verification. (See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)
14	INSPECT TIMING CHAIN • Inspect the timing chain. (See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)	—	Go to the next step.
15	PERFORM TIMING CHAIN LEARNING • Implement the timing chain learning. (See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)	—	Go to the next step.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Replicate the vehicle conditions at the time the DTC was detected using the following procedure. ― Start the engine. • Perform the DTC inspection for the PCM. (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 1.8].)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTCs DISPLAYED • Perform the DTC inspection. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.