DTC U250B:68 [DC-DC CONVERTER (Mazda M Hybrid)]
id140206302400
Outline
|
System malfunction location |
Error signal received from body control module (BCM) |
|---|---|
|
Detection condition
|
• The DC-DC converter (Mazda M Hybrid) receives an error signal from the body control module (BCM).
Precondition
• 1.5 s have elapsed after the ignition was switched ON (engine off or on)
• Voltage at DC-DC converter (Mazda M Hybrid) terminal 1A is 9-16 V for a continuous 1 s
|
|
Fail-safe
|
• Not applicable
|
|
Possible cause
|
• Body control module (BCM) malfunction
• DC-DC converter (Mazda M Hybrid) malfunction
|
|
System wiring diagram
|
• Not applicable
|
|
Connector diagram
|
• Not applicable
|
Diagnostic Procedure
|
Step |
Inspection |
Results |
Action |
|---|---|---|---|
|
1
|
RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
• Record the snapshot data.
|
—
|
Go to the next step.
|
|
2
|
INSPECT FOR OTHER RELATED DTCs
• Perform the DTC inspection for the DC-DC converter (Mazda M Hybrid).
(See DTC INSPECTION.)
• Are any of the following DTCs displayed?
|
Yes
|
Repair the malfunctioning location according to the applicable DTC troubleshooting.
|
|
No
|
Go to the next step.
|
||
|
3
|
VERIFY BODY CONTROL MODULE (BCM) DTC
• Perform the DTC inspection for the body control module (BCM).
(See DTC INSPECTION.)
• Are any DTCs displayed?
|
Yes
|
Repair the malfunctioning location according to the applicable DTC troubleshooting.
|
|
No
|
Go to the next step.
|
||
|
4
|
INSPECT BODY CONTROL MODULE (BCM) FOR MALFUNCTION DEPENDING ON REPEATABILITY
• Install/connect the part removed/disconnected during the troubleshooting procedure.
• Clear the DTC recorded in the memory.
(See CLEARING DTC.)
• Switch the ignition off, then ON (engine off).
• Perform the DTC inspection for the DC-DC converter (Mazda M Hybrid).
(See DTC INSPECTION.)
• Is the same Pending DTC present?
|
Yes
|
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
If the CAN communication is normal, perform the diagnosis from Step 1.
• If the malfunction recurs, replace the body control module (BCM).
Go to repair completion verification 1.
|
|
No
|
Go to the next step.
|
||
|
5
|
INSPECT BCM FOR MALFUNCTION DEPENDING ON REPEATABILITY AGAIN
• Perform the "Action for Non-repeatable Malfunction" procedure.
• Perform the DTC inspection for the DC-DC converter (Mazda M Hybrid).
(See DTC INSPECTION.)
• Is the same Pending DTC present?
|
Yes
|
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
If the CAN communication is normal, perform the diagnosis from Step 1.
• If the malfunction recurs, replace the body control module (BCM).
Go to repair completion verification 1.
|
|
No
|
The system is normal. (Explain to the customer that a malfunction was detected temporarily, but the vehicle is currently normal.)
Go to repair completion verification 2.
|
||
|
Repair completion verification 1
|
VERIFY THAT VEHICLE IS REPAIRED
• Install/connect the part removed/disconnected during the troubleshooting procedure.
• Clear the DTC recorded in the memory.
(See CLEARING DTC.)
• Switch the ignition off, then ON (engine off).
• Perform the DTC inspection for the DC-DC converter (Mazda M Hybrid).
(See DTC INSPECTION.)
• Is the same Pending DTC present?
|
Yes
|
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
If the CAN communication is normal, perform the diagnosis from Step 1.
• If the malfunction recurs, replace the DC-DC converter (Mazda M Hybrid), then go to the next step.
|
|
No
|
Go to the next step.
|
||
|
Repair completion verification 2
|
VERIFY IF OTHER DTCs DISPLAYED
• Perform the DTC inspection.
(See DTC INSPECTION.)
• Are any other DTCs displayed?
|
Yes
|
Repair the malfunctioning location according to the applicable DTC troubleshooting.
|
|
No
|
DTC troubleshooting completed.
|