NO.8 CRANKS NORMALLY BUT WILL NOT START [MZR-CD (RF Turbo)]

8	CRANKS NORMALLY BUT WILL NOT START
DESCRIPTION	• Starter cranks engine at normal speed but engine will not run. • Refer to symptom troubleshooting “No.5 Engine stalls” if this symptom appears after engine stall. • Fuel is in fuel tank. • Battery is in normal condition.
POSSIBLE CAUSE	• Poor fuel quality • Intake-air system restriction • Fuel line restriction • EGR system malfunction • Glow system malfunction • Fuel pressure sensor or related circuit malfunction • Suction control valve malfunction (built-in supply pump) • Fuel pressure limiter malfunction (built-in common rail) • Fuel leakage • Fuel filter clogging • Incorrect fuel injection timing • Erratic signal from CKP sensor • Erratic signal from CMP sensor • V-reference supply circuit malfunction • ECT sensor or related circuit malfunction • Supply pump malfunction • Fuel injector malfunction • Immobilizer system (PATS) and/or circuit malfunction (if equipped) • Low engine compression • Improper valve timing • PCM control repay malfunction Warning The following troubleshooting flow chart contains the fuel system diagnosis and repair procedures. Read the following warnings before performing the fuel system services: • Fuel vapor is hazardous. It can easily ignite, causing serious injury and damage. Always keep sparks and flames away from fuel. • Fuel line spills and leakage are dangerous. Fuel can ignite and cause serious injury or death and damage. Fuel can also irritate skin and eyes. To prevent this, always complete “BEFORE REPAIR PROCEDURE” and “AFTER REPAIR PROCEDURE” described in this manual.

CRANKS NORMALLY BUT WILL NOT START

DESCRIPTION

• Starter cranks engine at normal speed but engine will not run.

• Refer to symptom troubleshooting “No.5 Engine stalls” if this symptom appears after engine stall.

• Fuel is in fuel tank.

• Battery is in normal condition.

POSSIBLE CAUSE

• Poor fuel quality

• Intake-air system restriction

• Fuel line restriction

• EGR system malfunction

• Glow system malfunction

• Fuel pressure sensor or related circuit malfunction

• Suction control valve malfunction (built-in supply pump)

• Fuel pressure limiter malfunction (built-in common rail)

• Fuel leakage

• Fuel filter clogging

• Incorrect fuel injection timing

• Erratic signal from CKP sensor

• Erratic signal from CMP sensor

• V-reference supply circuit malfunction

• ECT sensor or related circuit malfunction

• Supply pump malfunction

• Fuel injector malfunction

• Immobilizer system (PATS) and/or circuit malfunction (if equipped)

• Low engine compression

• Improper valve timing

• PCM control repay malfunction

Warning

The following troubleshooting flow chart contains the fuel system diagnosis and repair procedures. Read the following warnings before performing the fuel system services:

• Fuel vapor is hazardous. It can easily ignite, causing serious injury and damage. Always keep sparks and flames away from fuel.

• Fuel line spills and leakage are dangerous. Fuel can ignite and cause serious injury or death and damage. Fuel can also irritate skin and eyes. To prevent this, always complete “BEFORE REPAIR PROCEDURE” and “AFTER REPAIR PROCEDURE” described in this manual.

STEP	INSPECTION	RESULTS	ACTION
1	Note • The following test should be perform for vehicles with immobilizer system. Go to Step 10 for vehicles without immobilizer system. Connect the WDS or equivalent to the DLC-2. Do following conditions appear? • Engine is not completely started. • DTC B1681 is displayed.	Yes	Both conditions appear: Go to Step 4.
No	Either or other condition appears: Go to the next step.
2	Is the coil connector securely connected to coil?	Yes	Go to the next step.
No	Connect the coil connector securely. Return to Step 1.
3	Does the security light illuminate?	Yes	Go to the next step.
No	Inspect the instrument cluster and wiring harness.
4	Connect the WDS or equivalent to the DLC-2 and retrieve the any DTCs. DTC B1213, B1342, B1600, B1601, B1602, B1681, B2103, B2431	Yes	Go to the appropriate DTC test.
No	Advanced keyless entry system is not equipped: Go to the next step. Advanced keyless entry system is equipped: Go to Step 8.
5	Is there continuity between PCM ground terminals 65, 85, 103, 104 and ground?	Yes	Go to the next step.
No	Repair or replace wiring harness.
6	Measure the voltage between PCM ground terminals 65, 85, 103, 104 and coil terminal C. Is the voltage below 1.0?	Yes	Go to the next step.
No	Repair or replace wiring harness.
7	Turn the engine switch to the ON position. Access the B+ PID. Is the B+ PID normal? Specification Battery voltage	Yes	Go to the next step.
No	Repair or replace wiring harness.
8	Disconnect the coil connector. Turn the engine switch to the ON position. Is there battery voltage at coil connector terminal D (harness-side)?	Yes	Go to the next step.
No	Repair or replace wiring harness between coil connector terminal D and fuse panel.
9	Inspect the following wiring harnesses and connectors. For advanced keyless entry is not equipped: • Between PCM terminal 89 and coil terminal A • Between PCM terminal 112 and coil terminal B For advanced keyless entry system equipped: • Between keyless CM terminal 3Y and coil terminal A • Between keyless CM terminal 3AA and coil terminal B • Between keyless CM terminal 4Z and PCM 87 • Between keyless CM terminal 4AA and PCM 95 Is there any malfunction (open or short circuit, terminal corrosion, etc.)?	Yes	Repair or replace malfunctioning part.
No	Go to the next step.
10	Inspect the following: • Fuel quality (e.g.: include water contamination, winter/summer blend) • Fuel line/fuel filter clogging • Intake-air system restriction Are all items normal?	Yes	Go to the next step.
No	Service if necessary. Repeat Step 10.
11	Note • Ignore DTC P0122, P0123, P0222 or P0223 while performing this test. Disconnect the APP sensor connector. Measure the voltage at APP sensor connector VREF terminal (terminal D and A) with the engine switch to the ON position. Specification 4.5—5.5 V Is the voltage normal?	Yes	Go to the next step.
No	Inspect the open or short circuit for wiring harness. • Between PCM terminal 82 and APP sensor terminal A • Between PCM terminal 63 and APP sensor terminal D
12	Connect the WDS or equivalent to the DLC-2. Turn the engine switch to the ON position. Retrieve the any DTCs. Are any DTC displayed?	Yes	DTC is displayed: Go to the appropriate DTC test. Communication error message is displayed: Inspect the following: • Open circuit between PCM control relay and PCM terminal 119 or 120 • Open circuit PCM control relay and PCM terminal 105 • PCM control relay stuck open • Open or poor ground circuit (PCM terminal 1, 2, 3, 114 or 117) • Poor connection vehicle body ground
No	No DTC is displayed: Go to the next step.
13	Inspect the glow system operation. (See RELAY INSPECTION.) Is the glow system operation normal?	Yes	Go to the next step.
No	Repair or replace malfunctioning part according to glow system operation results.
14	Inspect the fuel leakage from fuel pipe. Is any fuel leakage found on fuel pipe?	Yes	Repair or replace as necessary.
No	Go to the next step.
15	Visually inspect the CKP sensor and teeth of the pulse wheel. Are CKP sensor and teeth of pulse wheel normal?	Yes	Go to the next step.
No	Replace malfunctioning parts.
16	Measure the gap between CKP sensor and teeth of the pulse wheel. Specification 1.5—2.5 mm {0.059—0.098 in} Is the gap within specification?	Yes	Go to the next step.
No	Adjust the CKP sensor position.
17	Visually inspect the CMP sensor and teeth of the pulse wheel. Are the CMP sensor and teeth of the pulse wheel normal?	Yes	Inspect the following PIDs: (See PCM INSPECTION [MZR-CD (RF Turbo)].) • ECT • RPM If the PID value is not as specified, repair or replace malfunctioning parts. If the PID value is normal, go to the next step.
No	Replace malfunctioning parts.
18	Inspect the fuel pressure sensor. (See FUEL PRESSURE SENSOR INSPECTION [MZR-CD (RF Turbo)].) Is the fuel pressure normal?	Yes	Go to the next step.
No	Replace the common rail.
19	Inspect the suction control valve. (See SUCTION CONTROL VALVE INSPECTION [MZR-CD (RF Turbo)].) Is the suction control valve normal?	Yes	Go to the next step.
No	Replace the supply pump. (See SUPPLY PUMP REMOVAL/INSTALLATION [MZR-CD (RF Turbo)].)
20	Is the engine compression correct? (See COMPRESSION INSPECTION [MZR-CD (RF Turbo)].)	Yes	Go to the next step.
No	Inspect the following: • Damaged valve seat • Worn valve stem and valve guide • Worn or stuck piston ring • Worn piston, piston ring or cylinder • Improper valve timing Service if necessary.
21	Inspect the fuel injector. (See FUEL INJECTOR INSPECTION [MZR-CD (RF Turbo)].) Is the fuel injector normal?	Yes	Go to the next step.
No	Repair or replace as necessary.
22	Inspect the EGR system operation. Is the EGR system operation normal?	Yes	Remove and inspect the supply pump and common rail.
No	Repair or replace malfunctioning part according to EGR system operation results.
23	Verify test results. • If normal, return to the diagnostic index to service any additional symptoms. (See SYMPTOM DIAGNOSTIC INDEX [MZR-CD (RF Turbo)].) • If malfunction remains, inspect the related Service Information and perform repair or diagnosis. ― If the vehicle is repaired, the troubleshooting completed. ― If the vehicle is not repaired or additional diagnostic information is not available, reprogram the PCM if later calibration is available. Retest.

STEP

INSPECTION

RESULTS

ACTION

Note

• The following test should be perform for vehicles with immobilizer system. Go to Step 10 for vehicles without immobilizer system.

Connect the WDS or equivalent to the DLC-2.

Do following conditions appear?

• Engine is not completely started.

• DTC B1681 is displayed.

Yes

Both conditions appear:

Go to Step 4.

Either or other condition appears:

Go to the next step.

Is the coil connector securely connected to coil?

Yes

Go to the next step.

Connect the coil connector securely.

Return to Step 1.

Does the security light illuminate?

Yes

Go to the next step.

Inspect the instrument cluster and wiring harness.

Connect the WDS or equivalent to the DLC-2 and retrieve the any DTCs.

DTC

B1213, B1342, B1600, B1601, B1602, B1681, B2103, B2431

Yes

Go to the appropriate DTC test.

Advanced keyless entry system is not equipped:

Go to the next step.

Advanced keyless entry system is equipped:

Go to Step 8.

Is there continuity between PCM ground terminals 65, 85, 103, 104 and ground?

Yes

Go to the next step.

Repair or replace wiring harness.

Measure the voltage between PCM ground terminals 65, 85, 103, 104 and coil terminal C.

Is the voltage below 1.0?

Yes

Go to the next step.

Repair or replace wiring harness.

Turn the engine switch to the ON position.

Access the B+ PID.

Is the B+ PID normal?

Specification

Battery voltage

Yes

Go to the next step.

Repair or replace wiring harness.

Disconnect the coil connector.

Turn the engine switch to the ON position.

Is there battery voltage at coil connector terminal D (harness-side)?

Yes

Go to the next step.

Repair or replace wiring harness between coil connector terminal D and fuse panel.

Inspect the following wiring harnesses and connectors.

For advanced keyless entry is not equipped:

• Between PCM terminal 89 and coil terminal A

• Between PCM terminal 112 and coil terminal B

For advanced keyless entry system equipped:

• Between keyless CM terminal 3Y and coil terminal A

• Between keyless CM terminal 3AA and coil terminal B

• Between keyless CM terminal 4Z and PCM 87

• Between keyless CM terminal 4AA and PCM 95

Is there any malfunction (open or short circuit, terminal corrosion, etc.)?

Yes

Repair or replace malfunctioning part.

Go to the next step.

Inspect the following:

• Fuel quality (e.g.: include water contamination, winter/summer blend)

• Fuel line/fuel filter clogging

• Intake-air system restriction

Are all items normal?

Yes

Go to the next step.

Service if necessary.

Repeat Step 10.

Note

• Ignore DTC P0122, P0123, P0222 or P0223 while performing this test.

Disconnect the APP sensor connector.

Measure the voltage at APP sensor connector VREF terminal (terminal D and A) with the engine switch to the ON position.

Specification

4.5—5.5 V

Is the voltage normal?

Yes

Go to the next step.

Inspect the open or short circuit for wiring harness.

• Between PCM terminal 82 and APP sensor terminal A

• Between PCM terminal 63 and APP sensor terminal D

Connect the WDS or equivalent to the DLC-2.

Turn the engine switch to the ON position.

Retrieve the any DTCs.

Are any DTC displayed?

Yes

DTC is displayed:

Go to the appropriate DTC test.

Communication error message is displayed:

Inspect the following:

• Open circuit between PCM control relay and PCM terminal 119 or 120

• Open circuit PCM control relay and PCM terminal 105

• PCM control relay stuck open

• Open or poor ground circuit (PCM terminal 1, 2, 3, 114 or 117)

• Poor connection vehicle body ground

No DTC is displayed:

Go to the next step.

Inspect the glow system operation.

(See RELAY INSPECTION.)

Is the glow system operation normal?

Yes

Go to the next step.

Repair or replace malfunctioning part according to glow system operation results.

Inspect the fuel leakage from fuel pipe.

Is any fuel leakage found on fuel pipe?

Yes

Repair or replace as necessary.

Go to the next step.

Visually inspect the CKP sensor and teeth of the pulse wheel.

Are CKP sensor and teeth of pulse wheel normal?

Yes

Go to the next step.

Replace malfunctioning parts.

Measure the gap between CKP sensor and teeth of the pulse wheel.

Specification

1.5—2.5 mm {0.059—0.098 in}

Is the gap within specification?

Yes

Go to the next step.

Adjust the CKP sensor position.

Visually inspect the CMP sensor and teeth of the pulse wheel.

Are the CMP sensor and teeth of the pulse wheel normal?

Yes

Inspect the following PIDs:

(See PCM INSPECTION [MZR-CD (RF Turbo)].)

• ECT

• RPM

If the PID value is not as specified, repair or replace malfunctioning parts.

If the PID value is normal, go to the next step.

Replace malfunctioning parts.

Inspect the fuel pressure sensor.

(See FUEL PRESSURE SENSOR INSPECTION [MZR-CD (RF Turbo)].)

Is the fuel pressure normal?

Yes

Go to the next step.

Replace the common rail.

Inspect the suction control valve.

(See SUCTION CONTROL VALVE INSPECTION [MZR-CD (RF Turbo)].)

Is the suction control valve normal?

Yes

Go to the next step.

Replace the supply pump.

(See SUPPLY PUMP REMOVAL/INSTALLATION [MZR-CD (RF Turbo)].)

Is the engine compression correct?

(See COMPRESSION INSPECTION [MZR-CD (RF Turbo)].)

Yes

Go to the next step.

Inspect the following:

• Damaged valve seat

• Worn valve stem and valve guide

• Worn or stuck piston ring

• Worn piston, piston ring or cylinder

• Improper valve timing

Service if necessary.

Inspect the fuel injector.

(See FUEL INJECTOR INSPECTION [MZR-CD (RF Turbo)].)

Is the fuel injector normal?

Yes

Go to the next step.

Repair or replace as necessary.

Inspect the EGR system operation.

Is the EGR system operation normal?

Yes

Remove and inspect the supply pump and common rail.

Repair or replace malfunctioning part according to EGR system operation results.

Verify test results.

• If normal, return to the diagnostic index to service any additional symptoms.

(See SYMPTOM DIAGNOSTIC INDEX [MZR-CD (RF Turbo)].)

• If malfunction remains, inspect the related Service Information and perform repair or diagnosis.

― If the vehicle is repaired, the troubleshooting completed.

― If the vehicle is not repaired or additional diagnostic information is not available, reprogram the PCM if later calibration is available. Retest.

Mazdamanuals.com